Marble Slab Polishing Line Machine

The perfect polishing of marble slabs on industrial scale requires a modern line equipped with state-of-the-art technologies.
Pedrini is able to provide the most complete solutions ensuring high production performances, high degree of the polishing quality with low costs of operation and maintenance.
Pedrini polishing lines for marble slabs are designed, manufactured and installed to meet every requirement of each customer
Each polishing line is set according to the available spaces and is customized thanks to the use of a wide range of options, machines and auxiliary equipment designed to meet any kind of production need and automation level.
The polishing machine Galaxy B220MA is the basic machine in the polishing lines proposed by Pedrini.
All components have undergone structural inspection trough the FEM (Finite Element Method). The structural components surfaces are protected with three coats applied after sandblasting, while the small parts have undergone a cataphoresis corrosionproofing treatment.
The strong base, built in normalized steel work with large thickness longitudianl and transversal elements, has been further stiffened through continuous sloped structures that protect conveyor belt lower route by conveying water and eventual waste directly to ground.
All surfaces matching the upper structures have been machined through one sole positioning on the tool machine to achieve perfect units coupling.
The multi-clothe anti-slip conveyor belt is controlled by two large diameter rolls: a traction roll powered through an epicyclical gear motor, an idle roll equipped with tension devices.
Mobile beam, in heavy steel work, is designed as a sole body with a very rigid closed section. The beam slides in oil bath on hardened and ground large diameter rolls into housings, that are protected through fixed labyrinth guards, inside the bridges. Beam transversal movement is controlled by two gear motors, synchronized through a connecting shaft, which drive two helical tooth pinions tempered and ground with two racks fixed on the bridges.
Two special devices constantly lubricate with oil the contact between pinion and racks.
Two adjustable rolls units control mobile beam longitudinal position and contrast spindle vertical push working on hardened guides fixed onto bridges outer sides.This technology allows for very smooth beam transversal movement because it clears racks and pinions from vertical stress and renders pulling, instead of pressing, conveyor belt longitudinal action.

Suitable for milling and polishing of marble and granite
Milling head 1 and polishing heads 6
Max. working width 600 mm, max thickness 80 mm
Non length restrictions
Height adjustment by air cylinder
Automaticly adjustable
Cutter head and second polishing heads are optional extra

The construction,which is exceptionally strong and compact,provides perfect rigidity to the beams and to the entire driving system,for perfect side sliding and a very fast traversing speed.
Because of the in depth design and construction of all the components fo the head and the abrasive-holding plate,the tool evenly and regularly touches the material.
The FGMJ range of polishers , all noiseless and ergonomic, offers the greatest level of safety throughout the polishing process and during servicing.
All polishing, control and operating setting are set up and controlled by the user through an easy, user-friendly system and an operating setting management program while remaining simple and flexible.
The FGMJ range is available in a wide range of models with up to 24 polishing heads.
This big machine is more suitable for the artificail stone and big producetion marble cutting.

LEVIBRETON KFG 4600:THE TRENDSETTING IN MARBLE POLISHING

The Levibreton KFG 4600 polishing lines for marble are the soundest investment for companies requiring extreme productivity, top quality and operational simplicity, while maintaining budget-friendly operating and maintenance costs. Breton was the first company to develop machines for the continuous polishing of marble slabs, effecting a radical change in the sector. Today, thanks to its unrivalled years of experience,emerging concepts in automation, and digital/PC integration, increased and experience based qualitysimple maintenance procedures and low operating costs continue to be our high standard of value we achieve for our customers. This standard is expertly applied to our latest version Levibreton KFG 4600.

Levibreton KFG is a worldwide success with customer satisfaction unparalled in the contemporary market.

High Resale Value: thanks to their inherent quality, their ability to remain high-performance machines during all their service life and the readily available spare parts guaranteed by Breton, Levibreton KFG are much appealing to the second hand market and maintain a very high resale value even after several years (a fact not to be ignored when the purchase of a new polishing machine is considered).

This factor markedly improves the dynamic assett value of our client’s business.

Honing-polishing units

Made of anodized aluminium alloy,the spindles are specially designed for weight reduction and increased rigidity. The raising-lowering system is perfectly balanced

thanks to a pair of pistons with protected internal rods. The plates rise and lower in a flash, with a optimal contact with the slab surface, therefore slab edges are perfectly polished and the operating speed is maximized.Each head is equipped with a pressure regulator displaying the operating pressure on an analogue display, for simple monitoring and setting according to the optimal parameters for the material at hand.

Special Breton plates

For high efficiency, each spindle is equipped with a specifically engineered, Breton abrasive holding plate with a diameter of 550 mm and holding 9 abrasives,which ensures an extremely high removal capacity and work stability for a perfect and uniform polishing even up to the edges of the material. The special Breton plates are provided with an exclusive one-way shock-absorbing system ensuring the correct flexibility and a homogeneous and optimal working pressure. The results are an unequalled polishing quality as well as a lower consumption of abrasives.

Beam

The arc-welded steel beam has an ideal design with a box-type section in order to reduce weight and provide high stiffness. Interestingly, the beam is not drilled (and therefore weakened) to insert the honing units, which are fixed to the beam and contribute to increase its flexural strength. The spindle/beam assembly is thus extremely light and dynamic and enables fast acceleration/deceleration ramps.

Beam Drive

The beam is actuated by two rack and pinion systems driven by two gearmotors, which are fixed at each end of the beam and are mechanically synchronized. The gearmotors are driven by two brushlesstype motors controlled by special drives, which, besides enabling a sine movement of the beam, make it possible to keep the number of the beam strokes constant even when the slab width changes; this ensures a better polish quality and uniformity on the whole surface of the slab, edges included.

This system is extremely reliable and results proven, guaranteeing highly dynamic movements without stressing the mechanical components resulting in maximum uptime and maximum lifecycle. The beam working speed reaches 70 m/min. Furthermore, energy saving ensues from “energy recovery” drives that transfer to the electrical grid the energy generated by the braking when the beam motion slows down.

LEVIBRETON KFG 4600:

CLOSE TO PERFECTION

Levibreton KFG 4600 was designed on the basis of the extensive experience acquired on more than 1.300 “Levibreton” polishing machines sold throughout the world, using the latest design techniques.

Quality Function Deployment - QFD

The new Levibreton KFG 4600 originated from the Customers’ needs, from what the Customer really expects from the ideal machine.

Finite Element Method - FEM

All the critical components of the machine have been checked out using the Finite Element Method (FEM).

Failure Mode & Effect Analysis - FMEA

Particular care was given to the early detection of all the potential defects/critical points which may occur during the service life of the machine, identifying and implementing the appropriate corrective actions.

Support structure

The support structure is a distortion-proof,arc-welded steel monobloc provided with 12 sturdy supporting legs.The conveyor belt slides upon a thick steel top, which is milled all in one go to ensure perfect flatness, and is driven by a brushless type motor that guarantees a better control of the feed speed.

Beam sliding bridges

The beam ends are fixed to two shoulders sliding along sturdy, cast-iron bridges, which house hardened, ground and thick slideways with large diameter roller runners in an oil bath, and a micro pinion. The sliding components are protected by stainless steel labyrinth guards.

Slab profile and thickness detection

A photoelectric barrier reader detects the slab profile with 10x10 mm resolution while a sonar reader senses its thickness. This system allows to process even slabs with a polished surface (such as already polished or resin-treated slabs).The system controlling the automatic head liftinglowering,ensures the self-adjustment of the beam travel to the slab width and guarantees that the front,anti-splash and sound-deadening barriers are positioned automatically to match the slab thickness.

Water plant

Water is supplied to the heads by a common,large-diameter PVC piping that is stiffly fixed behind the spindles and connected to the spindle units by means of flexible, rubber pipes.An revolutionary system diverts water outside the spindle casing in the event of overflowing or clogging of the ducts, thus preventing excess water from coming into contact with the spindle internal components.

Automatic control of abrasives wear

This system performs continuous monitoring of the abrasive wear of each single head through video advice notes and warning signals before tools are completely worn out.

It also guarantees the minimal lifting of the heads at the forepart and rear end of the slab and their subsequent rapid descent, thus ensuring a better polishing of the edges and a higher operating speed.

Electric and electronic plant

The electric and electronic plant is wired with the “field-bus” technique that transmits digitally, through a single cable, all the PC signals to the different control units installed on the machine.Signal transmission is safe and identification of possible failures is greatly simplified.The stationary part of the machine is electrically connected to the mobile beam by a parallel sheathing system ensuring safer working conditions and a longer cable life.All the electric and electronic equipment, including the PC, is supplied by world top-brands, therefore the user can freely get technical assistance and spare parts directly from the manufacturer, virtually throughout the world.

Automatic centralized lubrication system

A centralized system, mainly consisting of a grease reservoir, a pump with double micrometer filtration system, sequential distributors and pipes for high-pressure, guarantees the automatic lubrication of either the spindle

units or the other moving parts of the machine. The system is warned about possible malfunctions by pressure sensors that easily pinpoint where the circuit is clogged.

Slab cleaning

A rubber wiper fixed at the back of the machine removes water from the slab surface.

A pneumatically controlled spindle, integral with the beam and holding a brush, cleans the slabs once they are polished. The spindle is raised and lowered automatically each time a slab passes through.

Accident-prevention,sound-deadening guards

A pressure regulator is installed on each single spindle in a high, ergonomic and safe position. Pressure is displayed on an analogue pressure gauge (upon request, manual selectors for lifting/lowering each single head can be supplied). The frontal, sliding panels for accident-prevention and sound-deadening have a sandwich-like structure and are made of ABS and polyurethane. Sound-deadening splash guards with a stainless steel sandwich-type structure are installed on the beam, in front of the heads, on the same level of the heads. Their positioning is motorized, vertical and automatic in order to match the slab thickness and they lift each time the abrasives need to be replaced.

Management and programming

The colour touch-screen and advanced, user-friendly software enable the main processing functions to be managed, including:

• option to store (and recall) different work programs for various types of material

• conveyor speed and synchronism of the whole line, including loaders and connection roller conveyors

• beam movement (speed, customized programming of the acceleration and deceleration

ramps)

• back-slipping correction on the anti-skid conveyor of badly-sawn or bent slabs, for both single slabs and packs of slabs

• continuous, automatic monitoring of the abrasive wear for each single head, with video advice notes and warning signals before the tool is completely worn out

• option of excluding all, some, or just one slab, or even a portion of a slab (head, end, corner).

It consists of the following elements:
- One roller blocks entry of 1.000 mm.
- One set goteron 4 hp.
- Six Polishers with drive motors and automatic stop programmatically de 2hp x 6 = 12h
- One top chamfering + One lower chamfering with drive and automatic stop programmatically.
- One roller block output 1.000 mm.
- All sealed oil bath heads.
- Heads in sealed boxes liquid fat.
- One conveyor belt with variator and regulation me chanical speed 2hp.
- Vulcanized conveyor belt drive pulley to ensure greater adherence.

- One stainless roller assembly with automatic pneumatic accompanying regulation up and down, depending on the thickness of the stone work. (For working different thicknesses continuously).
- One telescopic stand with wheels for long piece accompaniment.
- Thickness polish 6 cm.
- Dimensions of the machine: 6500 long x 1900 width x 1655 mm high ( with entry and exit rollers included ).
- Total installed power: 26hp

Machines for polishing pieces of marble or similar stone . Material to be polished is placed on the flat belt-conveyor moved by an hydraulic variator running at the proper working speed . The steel base plates of the machine are electro-welded with stainless steel hinged carters.
The working heads are independent units, each with its own motor, mandrel are chromium plated protected by a splash guard bellow, vertical motion and working pressure are pneumatically adjustable.

This machie can fit for composite tile, onyx back ground , marble slab and so one.

Parameter:

Full size: 5700*1800*1900mm grinding heads:16pcs

Head diameter:150mm processing width: 1200mm

Processing thickness: 10-50mm grinding speed: 0.2-0.8m/min

Gross power: 35kw gross weight : 6000kg

Griding tool: abrasive pad efficiency: 200m2/8hours

AUTOMATIC CALIBRATION AND POLISHING LINES FOR MARBLE STRIPS AND TILES
Excellence that is unrivaled.
LTotal and accessible quality has always been the top of the list of the GMM “mission”. The same commitment applied to the development of the more advanced version of the LMS series, automatic marble strips polishing machines. Following the construction philosophy that has always characterized the excellent Cemar product, the new series of polishing machines was developed using sturdy, precise and reliable mechanics. At the same time, cutting edge technological and electronic solutions were developed to ensure maximum quality of the processed material, high production yield and reduced processing waste. Result: high level performance, low running and maintenance costs with lasting durability. All at an affordable cost for the Customer.
UA customized solution for any requirement.
A customized solution for any requirement. To provide a solution for the specific needs of our Customers, the machines in the LMS series are produced in various sizes (650-850-1000) and different combinations of calibrators and polishing units. All LMS machines can work individually or positioned in production lines, even complex. This last application is easy to implement, thanks to the accompanying Software, developed entirely by GMM.
FEATURES
BASE
Monolithic high-thickness steel base electro-welded with rectified sliding surface.
INTERCHANGEABLE WEAR-PROOF SURFACES
Made with special steel (UBNW.1.446), thickness 3 mm, to guarantee planarity over time and facilitate maintenance.
SURFACE TREATMENT
All parts are treated inside our Company, with hand sand-blasting, cold galvanising and coating with bi-component epoxy base. On request, base and shoulders can be treated with Cataphoresis or hot dip galvanising. All screws are stainless steel.
3-BELT CONVEYOR
Driven by two large-diameter drums and inverter adjustable speed. Unique system to clean and lubricate the belt to ensure uniform sliding. The drive drum is coated with vulcanised rubber to prevent slipping and ensure flow smoothly.
SPINDLE HOLDER BEAM
Sliding on the shoulders fitted with roller cage in oil bath, protected by sealed stainless steel telescopic guards. Hardened steel sliding elements interchangeable and installed on the shoulders and bridge. The spindles are housed in the centre of the beam to ensure complete stability and eliminate any possibility of vibration.
BRIDGE TRANSLATION
With pinion and rack. Central gearmotor and antirotation bar with large diameter. Shifting speed controlled from inverter).
CALIBRATION UNITS
- Calibrator spindle made with heavy steel metalwork with rectified chromeplated sleeve, that slides through cast iron bushing to absorb vibrations during processing. On the spindle plate where it serves as a flywheel and is dynamically balanced, there are calibrator rings with diamond sectors installed on them (Ø 670-870-1050 mm). Electric drive can be 22 or 30 kW.
- An automatic system combined with motor absorption acts on conveyor speed, slowing it in case of excessive overload, making the spindle stop and automatically lift. The spindle is automatically repositioned with absolute precision when the operating cycle starts back up again. The calibrator is managed from the touch screen for all of its automatic and manual functions. Automatic positioning at the pre-selected height with centesimal precision.
POLISHING UNITS
- Cast iron polishing spindles, installed in the centre of the beam, with thick and rectified chrome-plated steel shaft, sliding on bronze bushing, complete with pneumatic cylinder for lifting abrasive carrier plate.
Each spindle is fitted with a pressure gauge to control pressure and counter-pressure to balance the head during the work.
- Motors. 7.5 or 11 kW motors with single or sequential start-up. Drive transmission through high-output pulleys and belts.
- Ø 470/510 aluminium alloy polishing plates complete with Frankfurt fittings for seven abrasives. They are equipped with a multidirectional shock absorbing system to ensure maximum operating homogeneity and efficiency of the abrasive.
- Automatic centralised lubrication system of the spindles with the possibility of setting quantities and intervention.
- Abrasive finished. The machine is equipped with a system to set the thickness of the piece being processed based on which, a sensor installed on each head, calls the attention of the operator to replace the abrasive, when finished.
- Slab-guide supports with screw movement through flywheel from a unique station, complete with stainless steel slab-guide.
- Material presence detection unit to control the automatic up/down movement of heads in case of discontinuity between pieces.
SAFETY AND PROTECTIONS
- Front PLT doors with interlocking limit switch to avoid opening before the spindles stop. Side and rear stainless steel guards, easy to inspect.
ELECTRONICS: THE "THINKING HEART" OF LMS
- Reliable. After careful testing, the parts are chosen from the leading companies in the specific sectors. To minimise the probability of failure or interference, a modern “can open” network system is installed on board, which drastically reduces the number of cables between sections.
- Software developed entirely by GMM, guaranteed over time, improvable and most of all customizable according to customer requirements.
- 12" Touch Screen. Interactive graphics for complete machine cycle management with start-up in sequence of spindles, conveyor motor and bridge motor. To manage spindle down/up based on piece presence.
To view the abrasive consumption status for each head.
- Data base. Broad possibility to store large amounts of informations about work done or in process.

FEATURES
BASE
Monolithic high-thickness steel base electro-welded with rectified sliding surface.
INTERCHANGEABLE WEAR-PROOF SURFACES
Made with special steel (UBNW.1.446), thickness 3 mm, to guarantee planarity over time and facilitate maintenance.
SURFACE TREATMENT
All parts are treated inside our Company, with hand sand-blasting, cold galvanising and coating with bi-component epoxy base. On request, base and shoulders can be treated with Cataphoresis or hot dip galvanising. All screws are stainless steel.
3-BELT CONVEYOR
Driven by two large-diameter drums and inverter adjustable speed. Unique system to clean and lubricate the belt to ensure uniform sliding. The drive drum is coated with vulcanised rubber to prevent slipping and ensure flow smoothly.
SPINDLE HOLDER BEAM
Sliding on the shoulders fitted with roller cage in oil bath, protected by sealed stainless steel telescopic guards. Hardened steel sliding elements interchangeable and installed on the shoulders and bridge. The spindles are housed in the centre of the beam to ensure complete stability and eliminate any possibility of vibration.
BRIDGE TRANSLATION
With pinion and rack. Central gearmotor and antirotation bar with large diameter. Shifting speed controlled from inverter).
CALIBRATION UNITS
- Calibrator spindle made with heavy steel metalwork with rectified chromeplated sleeve, that slides through cast iron bushing to absorb vibrations during processing. On the spindle plate where it serves as a flywheel and is dynamically balanced, there are calibrator rings with diamond sectors installed on them (Ø 670-870-1050 mm). Electric drive can be 22 or 30 kW.
- An automatic system combined with motor absorption acts on conveyor speed, slowing it in case of excessive overload, making the spindle stop and automatically lift. The spindle is automatically repositioned with absolute precision when the operating cycle starts back up again. The calibrator is managed from the touch screen for all of its automatic and manual functions. Automatic positioning at the pre-selected height with centesimal precision.
POLISHING UNITS
- Cast iron polishing spindles, installed in the centre of the beam, with thick and rectified chrome-plated steel shaft, sliding on bronze bushing, complete with pneumatic cylinder for lifting abrasive carrier plate.
Each spindle is fitted with a pressure gauge to control pressure and counter-pressure to balance the head during the work.
- Motors. 7.5 or 11 kW motors with single or sequential start-up. Drive transmission through high-output pulleys and belts.
- Ø 470/510 aluminium alloy polishing plates complete with Frankfurt fittings for seven abrasives. They are equipped with a multidirectional shock absorbing system to ensure maximum operating homogeneity and efficiency of the abrasive.
- Automatic centralised lubrication system of the spindles with the possibility of setting quantities and intervention.
- Abrasive finished. The machine is equipped with a system to set the thickness of the piece being processed based on which, a sensor installed on each head, calls the attention of the operator to replace the abrasive, when finished.
- Slab-guide supports with screw movement through flywheel from a unique station, complete with stainless steel slab-guide.
- Material presence detection unit to control the automatic up/down movement of heads in case of discontinuity between pieces.
SAFETY AND PROTECTIONS
- Front PLT doors with interlocking limit switch to avoid opening before the spindles stop. Side and rear stainless steel guards, easy to inspect.
ELECTRONICS: THE "THINKING HEART" OF LMS
- Reliable. After careful testing, the parts are chosen from the leading companies in the specific sectors. To minimise the probability of failure or interference, a modern “can open” network system is installed on board, which drastically reduces the number of cables between sections.
- Software developed entirely by GMM, guaranteed over time, improvable and most of all customizable according to customer requirements.
- 12" Touch Screen. Interactive graphics for complete machine cycle management with start-up in sequence of spindles, conveyor motor and bridge motor. To manage spindle down/up based on piece presence.
To view the abrasive consumption status for each head.
- Data base. Broad possibility to store large amounts of informations about work done or in process.

FEATURES
BASE
Monolithic high-thickness steel base electro-welded with rectified sliding surface.
INTERCHANGEABLE WEAR-PROOF SURFACES
Made with special steel (UBNW.1.446), thickness 3 mm, to guarantee planarity over time and facilitate maintenance.
SURFACE TREATMENT
All parts are treated inside our Company, with hand sand-blasting, cold galvanising and coating with bi-component epoxy base. On request, base and shoulders can be treated with Cataphoresis or hot dip galvanising. All screws are stainless steel.
3-BELT CONVEYOR
Driven by two large-diameter drums and inverter adjustable speed. Unique system to clean and lubricate the belt to ensure uniform sliding. The drive drum is coated with vulcanised rubber to prevent slipping and ensure flow smoothly.
SPINDLE HOLDER BEAM
Sliding on the shoulders fitted with roller cage in oil bath, protected by sealed stainless steel telescopic guards. Hardened steel sliding elements interchangeable and installed on the shoulders and bridge. The spindles are housed in the centre of the beam to ensure complete stability and eliminate any possibility of vibration.
BRIDGE TRANSLATION
With pinion and rack. Central gearmotor and antirotation bar with large diameter. Shifting speed controlled from inverter).
CALIBRATION UNITS
- Calibrator spindle made with heavy steel metalwork with rectified chromeplated sleeve, that slides through cast iron bushing to absorb vibrations during processing. On the spindle plate where it serves as a flywheel and is dynamically balanced, there are calibrator rings with diamond sectors installed on them (Ø 670-870-1050 mm). Electric drive can be 22 or 30 kW.
- An automatic system combined with motor absorption acts on conveyor speed, slowing it in case of excessive overload, making the spindle stop and automatically lift. The spindle is automatically repositioned with absolute precision when the operating cycle starts back up again. The calibrator is managed from the touch screen for all of its automatic and manual functions. Automatic positioning at the pre-selected height with centesimal precision.
POLISHING UNITS
- Cast iron polishing spindles, installed in the centre of the beam, with thick and rectified chrome-plated steel shaft, sliding on bronze bushing, complete with pneumatic cylinder for lifting abrasive carrier plate.
Each spindle is fitted with a pressure gauge to control pressure and counter-pressure to balance the head during the work.
- Motors. 7.5 or 11 kW motors with single or sequential start-up. Drive transmission through high-output pulleys and belts.
- Ø 470/510 aluminium alloy polishing plates complete with Frankfurt fittings for seven abrasives. They are equipped with a multidirectional shock absorbing system to ensure maximum operating homogeneity and efficiency of the abrasive.
- Automatic centralised lubrication system of the spindles with the possibility of setting quantities and intervention.
- Abrasive finished. The machine is equipped with a system to set the thickness of the piece being processed based on which, a sensor installed on each head, calls the attention of the operator to replace the abrasive, when finished.
- Slab-guide supports with screw movement through flywheel from a unique station, complete with stainless steel slab-guide.
- Material presence detection unit to control the automatic up/down movement of heads in case of discontinuity between pieces.
SAFETY AND PROTECTIONS
- Front PLT doors with interlocking limit switch to avoid opening before the spindles stop. Side and rear stainless steel guards, easy to inspect.
ELECTRONICS: THE "THINKING HEART" OF LMS
- Reliable. After careful testing, the parts are chosen from the leading companies in the specific sectors. To minimise the probability of failure or interference, a modern “can open” network system is installed on board, which drastically reduces the number of cables between sections.
- Software developed entirely by GMM, guaranteed over time, improvable and most of all customizable according to customer requirements.
- 12" Touch Screen. Interactive graphics for complete machine cycle management with start-up in sequence of spindles, conveyor motor and bridge motor. To manage spindle down/up based on piece presence.
To view the abrasive consumption status for each head.
- Data base. Broad possibility to store large amounts of informations about work done or in process.

FEATURES
BASE
Monolithic high-thickness steel base electro-welded with rectified sliding surface.
INTERCHANGEABLE WEAR-PROOF SURFACES
Made with special steel (UBNW.1.446), thickness 3 mm, to guarantee planarity over time and facilitate maintenance.
SURFACE TREATMENT
All parts are treated inside our Company, with hand sand-blasting, cold galvanising and coating with bi-component epoxy base. On request, base and shoulders can be treated with Cataphoresis or hot dip galvanising. All screws are stainless steel.
3-BELT CONVEYOR
Driven by two large-diameter drums and inverter adjustable speed. Unique system to clean and lubricate the belt to ensure uniform sliding. The drive drum is coated with vulcanised rubber to prevent slipping and ensure flow smoothly.
SPINDLE HOLDER BEAM
Sliding on the shoulders fitted with roller cage in oil bath, protected by sealed stainless steel telescopic guards. Hardened steel sliding elements interchangeable and installed on the shoulders and bridge. The spindles are housed in the centre of the beam to ensure complete stability and eliminate any possibility of vibration.
BRIDGE TRANSLATION
With pinion and rack. Central gearmotor and antirotation bar with large diameter. Shifting speed controlled from inverter).
CALIBRATION UNITS
- Calibrator spindle made with heavy steel metalwork with rectified chromeplated sleeve, that slides through cast iron bushing to absorb vibrations during processing. On the spindle plate where it serves as a flywheel and is dynamically balanced, there are calibrator rings with diamond sectors installed on them (Ø 670-870-1050 mm). Electric drive can be 22 or 30 kW.
- An automatic system combined with motor absorption acts on conveyor speed, slowing it in case of excessive overload, making the spindle stop and automatically lift. The spindle is automatically repositioned with absolute precision when the operating cycle starts back up again. The calibrator is managed from the touch screen for all of its automatic and manual functions. Automatic positioning at the pre-selected height with centesimal precision.
POLISHING UNITS
- Cast iron polishing spindles, installed in the centre of the beam, with thick and rectified chrome-plated steel shaft, sliding on bronze bushing, complete with pneumatic cylinder for lifting abrasive carrier plate.
Each spindle is fitted with a pressure gauge to control pressure and counter-pressure to balance the head during the work.
- Motors. 7.5 or 11 kW motors with single or sequential start-up. Drive transmission through high-output pulleys and belts.
- Ø 470/510 aluminium alloy polishing plates complete with Frankfurt fittings for seven abrasives. They are equipped with a multidirectional shock absorbing system to ensure maximum operating homogeneity and efficiency of the abrasive.
- Automatic centralised lubrication system of the spindles with the possibility of setting quantities and intervention.
- Abrasive finished. The machine is equipped with a system to set the thickness of the piece being processed based on which, a sensor installed on each head, calls the attention of the operator to replace the abrasive, when finished.
- Slab-guide supports with screw movement through flywheel from a unique station, complete with stainless steel slab-guide.
- Material presence detection unit to control the automatic up/down movement of heads in case of discontinuity between pieces.
SAFETY AND PROTECTIONS
- Front PLT doors with interlocking limit switch to avoid opening before the spindles stop. Side and rear stainless steel guards, easy to inspect.
ELECTRONICS: THE "THINKING HEART" OF LMS
- Reliable. After careful testing, the parts are chosen from the leading companies in the specific sectors. To minimise the probability of failure or interference, a modern “can open” network system is installed on board, which drastically reduces the number of cables between sections.
- Software developed entirely by GMM, guaranteed over time, improvable and most of all customizable according to customer requirements.
- 12" Touch Screen. Interactive graphics for complete machine cycle management with start-up in sequence of spindles, conveyor motor and bridge motor. To manage spindle down/up based on piece presence.
To view the abrasive consumption status for each head.
- Data base. Broad possibility to store large amounts of informations about work done or in process.

FEATURES
BASE
Monolithic high-thickness steel base electro-welded with rectified sliding surface.
INTERCHANGEABLE WEAR-PROOF SURFACES
Made with special steel (UBNW.1.446), thickness 3 mm, to guarantee planarity over time and facilitate maintenance.
SURFACE TREATMENT
All parts are treated inside our Company, with hand sand-blasting, cold galvanising and coating with bi-component epoxy base. On request, base and shoulders can be treated with Cataphoresis or hot dip galvanising. All screws are stainless steel.
3-BELT CONVEYOR
Driven by two large-diameter drums and inverter adjustable speed. Unique system to clean and lubricate the belt to ensure uniform sliding. The drive drum is coated with vulcanised rubber to prevent slipping and ensure flow smoothly.
SPINDLE HOLDER BEAM
Sliding on the shoulders fitted with roller cage in oil bath, protected by sealed stainless steel telescopic guards. Hardened steel sliding elements interchangeable and installed on the shoulders and bridge. The spindles are housed in the centre of the beam to ensure complete stability and eliminate any possibility of vibration.
BRIDGE TRANSLATION
With pinion and rack. Central gearmotor and antirotation bar with large diameter. Shifting speed controlled from inverter).
CALIBRATION UNITS
- Calibrator spindle made with heavy steel metalwork with rectified chromeplated sleeve, that slides through cast iron bushing to absorb vibrations during processing. On the spindle plate where it serves as a flywheel and is dynamically balanced, there are calibrator rings with diamond sectors installed on them (Ø 670-870-1050 mm). Electric drive can be 22 or 30 kW.
- An automatic system combined with motor absorption acts on conveyor speed, slowing it in case of excessive overload, making the spindle stop and automatically lift. The spindle is automatically repositioned with absolute precision when the operating cycle starts back up again. The calibrator is managed from the touch screen for all of its automatic and manual functions. Automatic positioning at the pre-selected height with centesimal precision.
POLISHING UNITS
- Cast iron polishing spindles, installed in the centre of the beam, with thick and rectified chrome-plated steel shaft, sliding on bronze bushing, complete with pneumatic cylinder for lifting abrasive carrier plate.
Each spindle is fitted with a pressure gauge to control pressure and counter-pressure to balance the head during the work.
- Motors. 7.5 or 11 kW motors with single or sequential start-up. Drive transmission through high-output pulleys and belts.
- Ø 470/510 aluminium alloy polishing plates complete with Frankfurt fittings for seven abrasives. They are equipped with a multidirectional shock absorbing system to ensure maximum operating homogeneity and efficiency of the abrasive.
- Automatic centralised lubrication system of the spindles with the possibility of setting quantities and intervention.
- Abrasive finished. The machine is equipped with a system to set the thickness of the piece being processed based on which, a sensor installed on each head, calls the attention of the operator to replace the abrasive, when finished.
- Slab-guide supports with screw movement through flywheel from a unique station, complete with stainless steel slab-guide.
- Material presence detection unit to control the automatic up/down movement of heads in case of discontinuity between pieces.
SAFETY AND PROTECTIONS
- Front PLT doors with interlocking limit switch to avoid opening before the spindles stop. Side and rear stainless steel guards, easy to inspect.
ELECTRONICS: THE "THINKING HEART" OF LMS
- Reliable. After careful testing, the parts are chosen from the leading companies in the specific sectors. To minimise the probability of failure or interference, a modern “can open” network system is installed on board, which drastically reduces the number of cables between sections.
- Software developed entirely by GMM, guaranteed over time, improvable and most of all customizable according to customer requirements.
- 12" Touch Screen. Interactive graphics for complete machine cycle management with start-up in sequence of spindles, conveyor motor and bridge motor. To manage spindle down/up based on piece presence.
To view the abrasive consumption status for each head.
- Data base. Broad possibility to store large amounts of information about work done or in process.

FEATURES
BASE
Monolithic high-thickness steel base electro-welded with rectified sliding surface.
INTERCHANGEABLE WEAR-PROOF SURFACES
Made with special steel (UBNW.1.446), thickness 3 mm, to guarantee planarity over time and facilitate maintenance.
SURFACE TREATMENT
All parts are treated inside our Company, with hand sand-blasting, cold galvanising and coating with bi-component epoxy base. On request, base and shoulders can be treated with Cataphoresis or hot dip galvanising. All screws are stainless steel.
3-BELT CONVEYOR
Driven by two large-diameter drums and inverter adjustable speed. Unique system to clean and lubricate the belt to ensure uniform sliding. The drive drum is coated with vulcanised rubber to prevent slipping and ensure flow smoothly.
SPINDLE HOLDER BEAM
Sliding on the shoulders fitted with roller cage in oil bath, protected by sealed stainless steel telescopic guards. Hardened steel sliding elements interchangeable and installed on the shoulders and bridge. The spindles are housed in the centre of the beam to ensure complete stability and eliminate any possibility of vibration.
BRIDGE TRANSLATION
With pinion and rack. Central gearmotor and antirotation bar with large diameter. Shifting speed controlled from inverter).
CALIBRATION UNITS
- Calibrator spindle made with heavy steel metalwork with rectified chromeplated sleeve, that slides through cast iron bushing to absorb vibrations during processing. On the spindle plate where it serves as a flywheel and is dynamically balanced, there are calibrator rings with diamond sectors installed on them (Ø 670-870-1050 mm). Electric drive can be 22 or 30 kW.
- An automatic system combined with motor absorption acts on conveyor speed, slowing it in case of excessive overload, making the spindle stop and automatically lift. The spindle is automatically repositioned with absolute precision when the operating cycle starts back up again. The calibrator is managed from the touch screen for all of its automatic and manual functions. Automatic positioning at the pre-selected height with centesimal precision.
POLISHING UNITS
- Cast iron polishing spindles, installed in the centre of the beam, with thick and rectified chrome-plated steel shaft, sliding on bronze bushing, complete with pneumatic cylinder for lifting abrasive carrier plate.
Each spindle is fitted with a pressure gauge to control pressure and counter-pressure to balance the head during the work.
- Motors. 7.5 or 11 kW motors with single or sequential start-up. Drive transmission through high-output pulleys and belts.
- Ø 470/510 aluminium alloy polishing plates complete with Frankfurt fittings for seven abrasives. They are equipped with a multidirectional shock absorbing system to ensure maximum operating homogeneity and efficiency of the abrasive.
- Automatic centralised lubrication system of the spindles with the possibility of setting quantities and intervention.
- Abrasive finished. The machine is equipped with a system to set the thickness of the piece being processed based on which, a sensor installed on each head, calls the attention of the operator to replace the abrasive, when finished.
- Slab-guide supports with screw movement through flywheel from a unique station, complete with stainless steel slab-guide.
- Material presence detection unit to control the automatic up/down movement of heads in case of discontinuity between pieces.
SAFETY AND PROTECTIONS
- Front PLT doors with interlocking limit switch to avoid opening before the spindles stop. Side and rear stainless steel guards, easy to inspect.
ELECTRONICS: THE "THINKING HEART" OF LMS
- Reliable. After careful testing, the parts are chosen from the leading companies in the specific sectors. To minimise the probability of failure or interference, a modern “can open” network system is installed on board, which drastically reduces the number of cables between sections.
- Software developed entirely by GMM, guaranteed over time, improvable and most of all customizable according to customer requirements.
- 12" Touch Screen. Interactive graphics for complete machine cycle management with start-up in sequence of spindles, conveyor motor and bridge motor. To manage spindle down/up based on piece presence.
To view the abrasive consumption status for each head.
- Data base. Broad possibility to store large amounts of information about work done or in process.

FEATURES
BASE
Monolithic high-thickness steel base electro-welded with rectified sliding surface.
INTERCHANGEABLE WEAR-PROOF SURFACES
Made with special steel (UBNW.1.446), thickness 3 mm, to guarantee planarity over time and facilitate maintenance.
SURFACE TREATMENT
All parts are treated inside our Company, with hand sand-blasting, cold galvanising and coating with bi-component epoxy base. On request, base and shoulders can be treated with Cataphoresis or hot dip galvanising. All screws are stainless steel.
3-BELT CONVEYOR
Driven by two large-diameter drums and inverter adjustable speed. Unique system to clean and lubricate the belt to ensure uniform sliding. The drive drum is coated with vulcanised rubber to prevent slipping and ensure flow smoothly.
SPINDLE HOLDER BEAM
Sliding on the shoulders fitted with roller cage in oil bath, protected by sealed stainless steel telescopic guards. Hardened steel sliding elements interchangeable and installed on the shoulders and bridge. The spindles are housed in the centre of the beam to ensure complete stability and eliminate any possibility of vibration.
BRIDGE TRANSLATION
With pinion and rack. Central gearmotor and antirotation bar with large diameter. Shifting speed controlled from inverter).
CALIBRATION UNITS
- Calibrator spindle made with heavy steel metalwork with rectified chromeplated sleeve, that slides through cast iron bushing to absorb vibrations during processing. On the spindle plate where it serves as a flywheel and is dynamically balanced, there are calibrator rings with diamond sectors installed on them (Ø 670-870-1050 mm). Electric drive can be 22 or 30 kW.
- An automatic system combined with motor absorption acts on conveyor speed, slowing it in case of excessive overload, making the spindle stop and automatically lift. The spindle is automatically repositioned with absolute precision when the operating cycle starts back up again. The calibrator is managed from the touch screen for all of its automatic and manual functions. Automatic positioning at the pre-selected height with centesimal precision.
POLISHING UNITS
- Cast iron polishing spindles, installed in the centre of the beam, with thick and rectified chrome-plated steel shaft, sliding on bronze bushing, complete with pneumatic cylinder for lifting abrasive carrier plate.
Each spindle is fitted with a pressure gauge to control pressure and counter-pressure to balance the head during the work.
- Motors. 7.5 or 11 kW motors with single or sequential start-up. Drive transmission through high-output pulleys and belts.
- Ø 470/510 aluminium alloy polishing plates complete with Frankfurt fittings for seven abrasives. They are equipped with a multidirectional shock absorbing system to ensure maximum operating homogeneity and efficiency of the abrasive.
- Automatic centralised lubrication system of the spindles with the possibility of setting quantities and intervention.
- Abrasive finished. The machine is equipped with a system to set the thickness of the piece being processed based on which, a sensor installed on each head, calls the attention of the operator to replace the abrasive, when finished.
- Slab-guide supports with screw movement through flywheel from a unique station, complete with stainless steel slab-guide.
- Material presence detection unit to control the automatic up/down movement of heads in case of discontinuity between pieces.
SAFETY AND PROTECTIONS
- Front PLT doors with interlocking limit switch to avoid opening before the spindles stop. Side and rear stainless steel guards, easy to inspect.
ELECTRONICS: THE "THINKING HEART" OF LMS
- Reliable. After careful testing, the parts are chosen from the leading companies in the specific sectors. To minimise the probability of failure or interference, a modern “can open” network system is installed on board, which drastically reduces the number of cables between sections.
- Software developed entirely by GMM, guaranteed over time, improvable and most of all customizable according to customer requirements.
- 12" Touch Screen. Interactive graphics for complete machine cycle management with start-up in sequence of spindles, conveyor motor and bridge motor. To manage spindle down/up based on piece presence.
To view the abrasive consumption status for each head.
- Data base. Broad possibility to store large amounts of informations about work done or in process.

Suitable for polishing slabs, headstones and kerbs.
Ideal for safe night shift operation, without operator.
Max. polishinh length unrestricted.

FEATURES
BASE
Monolithic high-thickness steel base electro-welded with rectified sliding surface.
INTERCHANGEABLE WEAR-PROOF SURFACES
Made with special steel (UBNW.1.446), thickness 3 mm, to guarantee planarity over time and facilitate maintenance.
SURFACE TREATMENT
All parts are treated inside our Company, with hand sand-blasting, cold galvanising and coating with bi-component epoxy base. On request, base and shoulders can be treated with Cataphoresis or hot dip galvanising. All screws are stainless steel.
3-BELT CONVEYOR
Driven by two large-diameter drums and inverter adjustable speed. Unique system to clean and lubricate the belt to ensure uniform sliding. The drive drum is coated with vulcanised rubber to prevent slipping and ensure flow smoothly.
SPINDLE HOLDER BEAM
Sliding on the shoulders fitted with roller cage in oil bath, protected by sealed stainless steel telescopic guards. Hardened steel sliding elements interchangeable and installed on the shoulders and bridge. The spindles are housed in the centre of the beam to ensure complete stability and eliminate any possibility of vibration.
BRIDGE TRANSLATION
With pinion and rack. Central gearmotor and antirotation bar with large diameter. Shifting speed controlled from inverter).
CALIBRATION UNITS
- Calibrator spindle made with heavy steel metalwork with rectified chromeplated sleeve, that slides through cast iron bushing to absorb vibrations during processing. On the spindle plate where it serves as a flywheel and is dynamically balanced, there are calibrator rings with diamond sectors installed on them (Ø 670-870-1050 mm). Electric drive can be 22 or 30 kW.
- An automatic system combined with motor absorption acts on conveyor speed, slowing it in case of excessive overload, making the spindle stop and automatically lift. The spindle is automatically repositioned with absolute precision when the operating cycle starts back up again. The calibrator is managed from the touch screen for all of its automatic and manual functions. Automatic positioning at the pre-selected height with centesimal precision.
POLISHING UNITS
- Cast iron polishing spindles, installed in the centre of the beam, with thick and rectified chrome-plated steel shaft, sliding on bronze bushing, complete with pneumatic cylinder for lifting abrasive carrier plate.
Each spindle is fitted with a pressure gauge to control pressure and counter-pressure to balance the head during the work.
- Motors. 7.5 or 11 kW motors with single or sequential start-up. Drive transmission through high-output pulleys and belts.
- Ø 470/510 aluminium alloy polishing plates complete with Frankfurt fittings for seven abrasives. They are equipped with a multidirectional shock absorbing system to ensure maximum operating homogeneity and efficiency of the abrasive.
- Automatic centralised lubrication system of the spindles with the possibility of setting quantities and intervention.
- Abrasive finished. The machine is equipped with a system to set the thickness of the piece being processed based on which, a sensor installed on each head, calls the attention of the operator to replace the abrasive, when finished.
- Slab-guide supports with screw movement through flywheel from a unique station, complete with stainless steel slab-guide.
- Material presence detection unit to control the automatic up/down movement of heads in case of discontinuity between pieces.
SAFETY AND PROTECTIONS
- Front PLT doors with interlocking limit switch to avoid opening before the spindles stop. Side and rear stainless steel guards, easy to inspect.
ELECTRONICS: THE "THINKING HEART" OF LMS
- Reliable. After careful testing, the parts are chosen from the leading companies in the specific sectors. To minimise the probability of failure or interference, a modern “can open” network system is installed on board, which drastically reduces the number of cables between sections.
- Software developed entirely by GMM, guaranteed over time, improvable and most of all customizable according to customer requirements.
- 12" Touch Screen. Interactive graphics for complete machine cycle management with start-up in sequence of spindles, conveyor motor and bridge motor. To manage spindle down/up based on piece presence.
To view the abrasive consumption status for each head.
- Data base. Broad possibility to store large amounts of informations about work done or in process.

FEATURES
BASE
Monolithic high-thickness steel base electro-welded with rectified sliding surface.
INTERCHANGEABLE WEAR-PROOF SURFACES
Made with special steel (UBNW.1.446), thickness 3 mm, to guarantee planarity over time and facilitate maintenance.
SURFACE TREATMENT
All parts are treated inside our Company, with hand sand-blasting, cold galvanising and coating with bi-component epoxy base. On request, base and shoulders can be treated with Cataphoresis or hot dip galvanising. All screws are stainless steel.
3-BELT CONVEYOR
Driven by two large-diameter drums and inverter adjustable speed. Unique system to clean and lubricate the belt to ensure uniform sliding. The drive drum is coated with vulcanised rubber to prevent slipping and ensure flow smoothly.
SPINDLE HOLDER BEAM
Sliding on the shoulders fitted with roller cage in oil bath, protected by sealed stainless steel telescopic guards. Hardened steel sliding elements interchangeable and installed on the shoulders and bridge. The spindles are housed in the centre of the beam to ensure complete stability and eliminate any possibility of vibration.
BRIDGE TRANSLATION
With pinion and rack. Central gearmotor and antirotation bar with large diameter. Shifting speed controlled from inverter).
CALIBRATION UNITS
- Calibrator spindle made with heavy steel metalwork with rectified chromeplated sleeve, that slides through cast iron bushing to absorb vibrations during processing. On the spindle plate where it serves as a flywheel and is dynamically balanced, there are calibrator rings with diamond sectors installed on them (Ø 670-870-1050 mm). Electric drive can be 22 or 30 kW.
- An automatic system combined with motor absorption acts on conveyor speed, slowing it in case of excessive overload, making the spindle stop and automatically lift. The spindle is automatically repositioned with absolute precision when the operating cycle starts back up again. The calibrator is managed from the touch screen for all of its automatic and manual functions. Automatic positioning at the pre-selected height with centesimal precision.
POLISHING UNITS
- Cast iron polishing spindles, installed in the centre of the beam, with thick and rectified chrome-plated steel shaft, sliding on bronze bushing, complete with pneumatic cylinder for lifting abrasive carrier plate.
Each spindle is fitted with a pressure gauge to control pressure and counter-pressure to balance the head during the work.
- Motors. 7.5 or 11 kW motors with single or sequential start-up. Drive transmission through high-output pulleys and belts.
- Ø 470/510 aluminium alloy polishing plates complete with Frankfurt fittings for seven abrasives. They are equipped with a multidirectional shock absorbing system to ensure maximum operating homogeneity and efficiency of the abrasive.
- Automatic centralised lubrication system of the spindles with the possibility of setting quantities and intervention.
- Abrasive finished. The machine is equipped with a system to set the thickness of the piece being processed based on which, a sensor installed on each head, calls the attention of the operator to replace the abrasive, when finished.
- Slab-guide supports with screw movement through flywheel from a unique station, complete with stainless steel slab-guide.
- Material presence detection unit to control the automatic up/down movement of heads in case of discontinuity between pieces.
SAFETY AND PROTECTIONS
- Front PLT doors with interlocking limit switch to avoid opening before the spindles stop. Side and rear stainless steel guards, easy to inspect.
ELECTRONICS: THE "THINKING HEART" OF LMS
- Reliable. After careful testing, the parts are chosen from the leading companies in the specific sectors. To minimize the probability of failure or interference, a modern “can open” network system is installed on board, which drastically reduces the number of cables between sections.
- Software developed entirely by GMM, guaranteed over time, improvable and most of all customizable according to customer requirements.
- 12" Touch Screen. Interactive graphics for complete machine cycle management with start-up in sequence of spindles, conveyor motor and bridge motor. To manage spindle down/up based on piece presence.
To view the abrasive consumption status for each head.
- Data base. Broad possibility to store large amounts of information about work done or in process.

The NPM polishing machines are available also in the combined version for calibrating and polishing of marble slabs. The first mobile bridge (PM version) installs calibrating spindles, capable of calibrating the useful working width, the second bridge installs honing spindles, the number depending on the version, for total honing/polishing of the width working efficiency of 2150 mm.

FEATURES
BASE
Monolithic high-thickness steel base electro-welded with rectified sliding surface.
INTERCHANGEABLE WEAR-PROOF SURFACES
Made with special steel (UBNW.1.446), thickness 3 mm, to guarantee planarity over time and facilitate maintenance.
SURFACE TREATMENT
All parts are treated inside our Company, with hand sand-blasting, cold galvanising and coating with bi-component epoxy base. On request, base and shoulders can be treated with Cataphoresis or hot dip galvanising. All screws are stainless steel.
3-BELT CONVEYOR
Driven by two large-diameter drums and inverter adjustable speed. Unique system to clean and lubricate the belt to ensure uniform sliding. The drive drum is coated with vulcanised rubber to prevent slipping and ensure flow smoothly.
SPINDLE HOLDER BEAM
Sliding on the shoulders fitted with roller cage in oil bath, protected by sealed stainless steel telescopic guards. Hardened steel sliding elements interchangeable and installed on the shoulders and bridge. The spindles are housed in the centre of the beam to ensure complete stability and eliminate any possibility of vibration.
BRIDGE TRANSLATION
With pinion and rack. Central gearmotor and antirotation bar with large diameter. Shifting speed controlled from inverter).
CALIBRATION UNITS
- Calibrator spindle made with heavy steel metalwork with rectified chromeplated sleeve, that slides through cast iron bushing to absorb vibrations during processing. On the spindle plate where it serves as a flywheel and is dynamically balanced, there are calibrator rings with diamond sectors installed on them (Ø 670-870-1050 mm). Electric drive can be 22 or 30 kW.
- An automatic system combined with motor absorption acts on conveyor speed, slowing it in case of excessive overload, making the spindle stop and automatically lift. The spindle is automatically repositioned with absolute precision when the operating cycle starts back up again. The calibrator is managed from the touch screen for all of its automatic and manual functions. Automatic positioning at the pre-selected height with centesimal precision.
POLISHING UNITS
- Cast iron polishing spindles, installed in the centre of the beam, with thick and rectified chrome-plated steel shaft, sliding on bronze bushing, complete with pneumatic cylinder for lifting abrasive carrier plate.
Each spindle is fitted with a pressure gauge to control pressure and counter-pressure to balance the head during the work.
- Motors. 7.5 or 11 kW motors with single or sequential start-up. Drive transmission through high-output pulleys and belts.
- Ø 470/510 aluminium alloy polishing plates complete with Frankfurt fittings for seven abrasives. They are equipped with a multidirectional shock absorbing system to ensure maximum operating homogeneity and efficiency of the abrasive.
- Automatic centralised lubrication system of the spindles with the possibility of setting quantities and intervention.
- Abrasive finished. The machine is equipped with a system to set the thickness of the piece being processed based on which, a sensor installed on each head, calls the attention of the operator to replace the abrasive, when finished.
- Slab-guide supports with screw movement through flywheel from a unique station, complete with stainless steel slab-guide.
- Material presence detection unit to control the automatic up/down movement of heads in case of discontinuity between pieces.
SAFETY AND PROTECTIONS
- Front PLT doors with interlocking limit switch to avoid opening before the spindles stop. Side and rear stainless steel guards, easy to inspect.
ELECTRONICS: THE "THINKING HEART" OF LMS
- Reliable. After careful testing, the parts are chosen from the leading companies in the specific sectors. To minimize the probability of failure or interference, a modern “can open” network system is installed on board, which drastically reduces the number of cables between sections.
- Software developed entirely by GMM, guaranteed over time, improvable and most of all customizable according to customer requirements.
- 12" Touch Screen. Interactive graphics for complete machine cycle management with start-up in sequence of spindles, conveyor motor and bridge motor. To manage spindle down/up based on piece presence.
To view the abrasive consumption status for each head.
- Data base. Broad possibility to store large amounts of information about work done or in process.

The LM 2100 RS is available in the combined version for polishing slabs and for calibrating and polishing strips and/or tiles. The calibrating is performed by special spindles that can be equipped with diamond tools with useful working width of 650 or 1000 mm according to the version. The calibrating spindles are installed at a fixed position at the entry of the polishing machine while the dressing spindles are installed on a mobile bridge and can operate on a useful width of 2100 mm.

AUTOMATIC BELT POLISHING MACHINE FOR MARBLE SLABS
Thanks to CEMAR’s over twenty years experience in surface treatment of marble and granite, GMM present the most advanced version of LMS 2100 belt polishing machine for marble slabs. Respecting the philosophy that has always characterized the excellent CEMAR product, the new series of polishing machines for marble slabs is made using robust, accurate and reliable mechanics. In conjunction, the machine has advanced electronic and technology solutions to ensure maximum quality of work, high production yields and reduction of waste. All this ensure low running and maintenance costs, with high durability.
FEATURES
BASE
In sturdy electro-welded steel structure with rectified sliding plane covered with replaceable wear plates made of 3 mm thick special steel to ensure flatness and easy maintenance over time.
SURFACE TREATMENTS
All components are treated in our company with sandblasting by hand, cold galvanizing and painting with two component epoxy primer. On request, base and shoulders can be hot dip galvanized.
BELT
Pulled by two drums of large diameter. Speed adjustable by inverter. Two unique systems for cleaning and lubricating the belt to ensure flow smoothly.
BEAM
For spindle housing in a sturdy and rigid structure of welded steel. Sliding on the shoulders equipped with roller bearing in oil bath, protected by telescopic guards in stainless steel. Sliding elements made of hardened steel interchangeable and mounted both on the shoulders and on the bridge. The spindles are housed at the center of the beam to ensure complete stability and to avoid any possible vibration.
TRANSLATION OF THE BRIDGE
With rack and pinion. Starting from the version with 12 spindles, the transmission takes place with 2 gearmotors coupled at the bridge ends. Travel speed controlled by inverter.
POLISHERS SPINDLES
In cast iron, with thick chrome-plated steel grounded shaft, sliding on bronze bushes, complete with pneumatic cylinder for raising the abrasives carrying plates. Each spindle is equipped with a gauge for the control of pressure and counterpressure, necessary to balance the head during the working. The cooling water passes inside the shaft for a better and uniform distribution on the materials being processed.
MOTORS
11 kW/15 HP motors, with individual or in sequence start-up. Motion transmission with high performance belts.
ELECTRONICS: “THINKING HEART” OF THE LMS 2100
- Reliable. After careful controls, components are selected among leading companies in specific sectors (mainly Siemens or Schneider-Telemcanique).
- To make minimum the probability of failure or interference, on board of the machine is adopted modern network system "can open" which drastically reduces the number of cables between one section and the other.
- Software. Developed entirely in GMM, guaranteed over time, especially improved and customized according to customer requirements.
- Inverters. The roller conveyors and specific rollers in the entry are handled by inverters, like all the other moving parts, to balance the fl ow of material and optimize the speed of each step.
- Optical detector 120 photocells, to scan in a sequence the shape of entering slabs, done in RS485 protocol (noise free), it transmits the shape of the slab to the control unit to better manage the ascent and descent of the heads, according to the various selectable working cycles.
- Ultrasonic sensor, positioned at the entrance, to detect the material thickness. Enables fully automatic management of the abrasives consumption of each single head.
- Automatic lubrication management, for planning the quantity of lubricant to be dispensed and the dispensing times.
- Touch Screen 12". Monitor with "easy to use" interface, interactive graphics for the complete management of the machine cycle with sequential startup spindle motors, belt and bridge motors. It drives the spindles up-down stroke according to the shape of slabs. Display of abrasive consumption status for each head.
- Data base. Large possibility to store various information about the work done or in progress.

The HPM polishing machines are available in the version for strips, with useful working width of 650 or 1000 mm and are supplied in combined solutions for calibrating and dressing-polishing. The spindle of the HPM polishing machines can house plates 580 mm. in diameter. The calibration takes place with rotating plates equipped with diamond tools., installed in a fixed or mobile position.

FEATURES
PLT GOLD SERIES - TANGENTIAL HEAD
It has a range of very important features that differentiate it from the competition: treated aluminium box to obtain lightness and elasticity for absorbing blows, arm opening and closing by means of a hardened, cemented and ground cam system, total consumption of the abrasive, main shaft reinforced, bearings of the highest quality and ready for the fl at marble connection.
PSG GOLD SERIES - PLANETARY HEAD
It is built with a treated aluminium box for lightness and elasticity when absorbing blows, hardened and ground gears manufactured by our numerical control centres and bronze covers for simple economic maintenance.

REFERENCE 103 006 016
THICKNESS MAX A POLISH 100 mm
MACHINE PULICANTOS
DIAMETER PADS 130 mm
MARK / MODEL SSX MD.TE
PROGRAMMING DIGITAL
YEAR OF MANUFACTURING 2006
GREASE MANUAL
HEADS HYDRAULICS
OVERALL DIMENSIONS 7000 X 2300 mm
NUMBER OF POLISH 6
POWER 40 CV
CHAMFERING 1 TOP + 1 BOTTOM
SWING SISTEM BY RODS MAKES STRAIGHT EDGE AND ROUND

SIMEC The Testarossa C8 have a higher removal capacity, guaranteeing a great planarity and an excellent finishing of the material processed. The C8 heads, thanks to their characteristics, are used in the calibrating of quartz agglomerate slabs. The C8 heads are installed together with the special calibrating spindle mod. FX that due to its double motor allows independent adjustment of the rotation speed of the head and tools.

These products have proven to have a higher removal capacity, guaranteeing a great planarity and an excellent finishing of the material processed. The C2 and C3 heads, thanks to their characteristics, are used in the calibrating of both slabs, strips and tiles of granite. The C2 and C3 heads are installed together with the special calibrating spindle that due to its double motor allows independent adjustment of the rotation speed of the head and tools.

Specifically designed to be used with diamond tools, this type of head is particularly suitable for the roughing phase of hard materials. Characterised by high removal capacity and perfect flatness of the material, this head also ensures negligible wear of tools and high reliability.

Dual-system continuous levelling machine for granite "Levibreton Mod. KCP 60"

Machine for levelling granite strips, moving on a conveyor belt, us-ing a series of diamond rollers and pneumatic tools.
This machine is based on a revolutionary processing concept, covered by Breton patent, which employs calibrating spindles MC6 with double motorization: in each spindle, the first motor provides the low-speed rotation of the roller-holding head (2,2 kW power), while the second motor provides the high-speed rotation of six radial rollers equipped with diamond tools (22 kW power).
This new technology offers the following advantages:
a) rapid adjustment of the working width, as the calibrating section does not need for any varia-tion;
b) perfect surface levelling;
c) "fine-honed" surface finish, which makes it possible to reduce the number of the following lev-elling units, and consequently, the dressing costs.

Our Sizing and Polishing Line have loaded today for Dervisoglu Marble.
Have a good trip !

Fujian Xianda APM-350-2000-10 ,This machine fix circular slab by vacuum, it is better than fix by grippng two sides . And solve the problem which caused verticality and inclination mistake after trimming. It won't brock the edge of column slabs. Also it adopts linear guide ,multi-polishing heads, PLC system control. It has the feature of high precision ,high efficiency ,easy operation , etc. It is the ideal equipment for column slab polishing.

This machine is used for polishing small slabs of marble.

PLATE MARBLE POLISHING MACHINE
This efficiency proved machine has been specially designed for thickness gauging and polishing of strips with cut ends. And max. width dimensions 2100 mm. The new PLX 2000 series supported with high technology, can reach top production speeds, whilst reducing consumption, maintenance and depreciation. THE SPINDLE: The PLX 2000 G features powerful, high precision polishing spindles with pneumatic working pressure which easily and perfect polishing any kind of granite.The spindles are entirely processed on CNC using highest quality of the material. Every spindle is assembled in the center of the mobile beam.
The spindles are working at their centre of gravity on the rotation axis so the mechanical play is reduced and this eliminates maintenance works.
The spindle has two electrical motors special tothed belt transmission system that the motors drive by prevents loosening or slipping of the spindles even under stress. The pneumatic system makes use through counter air pressure of the considerable spindle mass to obtain stability to the polishing heads. Counter pressure pneumatic system allows to polish fragile and delicate materials, with low working pressure. The machine controls the lifting movement of the spindles automaticly according to feeding the material
THE BEAM: The spindle holding beam is made of electro - welded steel and moves on exteremely wear resistant cast iron and alloyed bronze slideways. Sliding components are working in an oilbath and protected by stainless steel labyrinth seals. Beam movement is done by two motor reducer system located at the end of the beam to ensure constant and regular beam motion. The beam moves on two side bridges made of electrowelded steel and it has very strong structure to eliminate vibration during the operation. The synchronization shaft located the rear side of the beam provides uniform movement at both beam ends. The bridge moves on bronze alloyed slideways working in oil bath The adjustments, quick format changes and performing very rapid arrangements are some minor themes of high technological feedbacks manufactured for productive flexibility in this machine.

THE TABLE: The uniblock steel chasis designed to provide high rigidity and stability. The surface of the table covered by hard stainless steel to ensure long life of table and conveyor belt. At the ends of the table 2 turned belt drive rollers are installed one of which is free moving, and other one is motorized. The belt drive rollers are made of special steel. The belt is driven by a planetary type gear –motor to provide safe and uniform movement during the process. The conveyor belt speed adjustment is obtained by electronic frequency inverter.
ELECTRICAL AND WATER CONNECTION: The electrical and water connection between machine stationary part and the mobile beam is made by flexible cable chains which assure safer working conditions and a longer life for components. The polishing heads cooling water feed is performed by steel pipes which operates in a fixed position in the center of the spindle. The water cooling pipes can be removed very easily for the periodical clearing for calcereous substances. THE HEADS: A polishing head with swinging arms to hold the tools (abrasive or diamond) is mounted on each spindle. The motion of each swinging arm is obtained by an extremely precise, kinematical and mechanical system that reduce any clearance therefore ensuring low noise and long tools life. The particular geometry, the oscillation angle and frequency of the arms help to obtain high tools efficiency. The lubrication of the mechanical parts is by means of permanent oil bath with automatic lubrication pump. The even operation of the abrasive-holder arm controlled by a gear kinematical motion and the axial elasticity of the head provide large removals and high slab polishing level.
MACHINE CONTROL: The machine is controlled by a PLC (programable logic control) system with a 12 inch Touch Screen color panel for managing to synchronize all the processing parameters by easy interface and operator controls.
PAINT TREATMENT: Surface protected with two coats of bicomponent epoxy paint applied after sand blasting operation.