Stone Tile Cutting Machines

ATM 1500-2500-3500 Multiple cross-cutting machine for marble and granite

Longitudinal cutting machines, very sturdy and reliable that can cut strips wide up to 50 mm (60 RAF). These longitudinal cutting machines are available in manual or sequential versions. Spindles fitted are 1 to 3 and can cut thickness up to 40 mm for granite and 60 mm for marble in a single pass.

MTX 700/1 is a one-head multi-disc cutting machine, and it is used for reject recovery in marble; it is very rugged with a shaft to hold the discs which is mounted by both sides to obtain stability and lack of vibrations. This solution allows to cut in one run the materials of big thickness. On the shaft that holds the discs, it is possible to mount more than one cutting disc spaced by proper separators in order to obtain different sizes. The conveyor belt of piezes in rubber with high adhesion is large 700mm and its speed is adjustable through inverter. The head is adjustable vertically with an electric control. With an adequate motor it allows to cut till 80/100 mm of thickness. The cutting speed of 1/7 ml/min is adjustable electrically with a manual control for different thickness.

MTP are automatic machines for multiple linear cutting with diamond discs.
Suitable for cutting ceramic tiles of any kind, marble, granite, glass and bricks.
MTP 500/700/950/1300/1600/1900/2200 differentiate from each other for the width of the relevant conveyor belt and can be delivered with two or three cutting heads, to allow the choice of the most appropriate type according to the quantities or the sizes to be cut.
An essential characteristic of the MTPs is the fact that the disc support shaft is stable and doesn't vibrate as it is fastened on both sides. The lack of vibrations guarantees the excellent quality of the cut made.
With two disc support heads, the first is used to perform the pre-cut and the second the cut, thus achieving high production speeds with excellent finish results.
With three heads, on the other hand, there are certain advantages,
1) by using the second head you can chamfer by fitting chamfering discs shaped at 90°, thus obtaining a complete cut with superior chamfering.
2) by carrying out two pre-cuts with the first and second heads and the final cut with the third you get higher production and the possibility to cut thicknesses off up to 25/30 mm on materials such as granite or porcelain stoneware without drastically slowing down the cutting speed.
As the frame is the same length for all models it is in any case possible to subsequently fit the third head onto the 2-head cutting machine.
Thanks to their very sturdy structure, the MTPs can be fitted with motors with power up to 22kw with special tools for cutting mosaics automatically up to sizes of 10x10 mm.

MTP are automatic machines for multiple linear cutting with diamond discs.
Suitable for cutting ceramic tiles of any kind, marble, granite, glass and bricks.
MTP 500/700/950/1300/1600/2200 differentiate from each other for the width of the relevant conveyor belt and can be delivered with two or three cutting heads, to allow the choice of the most appropriate type according to the quantities or the sizes to be cut.
An essential characteristic of the MTPs is the fact that the disc support shaft is stable and doesn't vibrate as it is fastened on both sides. The lack of vibrations guarantees the excellent quality of the cut made.
With two disc support heads, the first is used to perform the pre-cut and the second the cut, thus achieving high production speeds with excellent finish results.
With three heads, on the other hand, there are certain advantages,
1) by using the second head you can chamfer by fitting chamfering discs shaped at 90°, thus obtaining a complete cut with superior chamfering.
2) by carrying out two pre-cuts with the first and second heads and the final cut with the third you get higher production and the possibility to cut thicknesses off up to 25/30 mm on materials such as granite or porcelain stoneware without drastically slowing down the cutting speed.
As the frame is the same length for all models it is in any case possible to subsequently fit the third head onto the 2-head cutting machine.
Thanks to their very sturdy structure, the MTPs can be fitted with motors with power up to 22kw with special tools for cutting mosaics automatically up to sizes of 10x10 mm.

MTP 1300-1600-1900-2200/3 - BIG SIZES CUTTING MACHINES

MRY machine makes incisions on the board of materials of gres porcelain, agglomerated, granite, marble and terrace allowing the insertion of supporting clips for the ventilated facades.

MultiCut 350/550 - Programmable multi-spindle automatic saw with revolving table
Breton Multicut is a programmable multi-spindle automatic saw with a revolving worktable and is designed for cutting both natural and engineered stone slabs to any required size.
Breton Multicut is designed and developed to offer high-production and cutting performance combined with improved operational flexibility and a sophisticated and advanced slab optimisation system.
The work cycle - longitudinal cuts, work-table rotation, transversal cuts - is fully automatic and computer managed. Slab loading and product unloading operations can be automated to meet specific requirements. Precise and accurate cutting. The work cycles are programmed on the machine monitor and can be stored and then recalled whenever required. Depending on slab thickness, the slab can be cut in plunge-cut or step-cut mode. The “scanner” system scans the shape of the slab and records surface defects, and a special software elaborates and defines the best cutting cycle based on the slabs available and work orders programmed in the system. The result is maximum production optimisation.
Slab surface optimisation system
Breton Multicut can in real time optimise slab surface by automatically selecting the most appropriate cutting cycle to process the work orders previously programmed in the computer system which controls and manages the production line.
When slabs are fed-into Breton Multicut, a scanner scans the shape and size of the slabs and the operator can mark out any defects, holes or cracks in the surface. Based on the information transmitted by the scanner and on the programmed work orders, a purposely developed software manages the machines and equipment forming the production line simultaneously. This software can also receive work orders through a local access network from the office PC. The work order can include diverse formats of tiles which are identified in the order utilising just the measurements for length and width. For each format the required quantity is defined and is automatically updated based on the number of cutting cycles for each slab processed until the order is completed. Slab cutting, based on the information received from the scanner, is optimised to reduce waste. Even slabs with surface defects such as holes, stains, marks etc. are optimised using this system. The scanner records the defects of the slabs and
sends prompts to the software only if the defects have been previously marked out by the operator who simply positions over the defect (whether it is a hole, stain, crack etc…) a piece of non-reflecting matt material (e.g. standard household carpet). When the slab passes under the scanner, the scanner
reads the covered areas as if part of the slab is missing identifying these zones as part/s of the slab which cannot be utilised in production. Prompts are then sent to the main system PC and the software elaborates the information and defines the best cycle to optimise production. The operator removes the material used to cover the defects which can be reused or thrown away. The information is then graphically displayed on the monitor indicating the percentage of material processed. And the waste produced….. There are several cutting and optimisation options: For sawing strips (longitudinal or transversal or mixed) the system will automatically standardize the cutting pattern so as to reduce the machine’s cycle time for very complex cutting patterns. This function brings together, where possible, strips having the same cuts so that they can be sawn in a single work cycle.

2nd hand Strip Cutting,Edge Trimming Machine
Second Hand Multidisc Cutter Machine

MST 350 45° Miter cutter
Heavy duty miter saw. The rigid structure eliminates vibrations and gives a sharp edge on your miters.
Retractable alignment provides for easy loading. Pneumatic cylinders firmly hold the stone in place on the machine table and can be adjusted for narrow strips, ensuring a straight mitre every time.
Available with optional 3 motors to mount polishing pads for polish flat edges.

MST – 45°Miter Cutter
Machine made in heavy duty aluminum, with high precision ball linear guides, ensures precise movements. This machine moves in automatic.

Vertical Decorative Hydraulic Stone Splitting Machine
Max. Stone breaking height: 300 mm

Irregular stone veneer saw cutting machine for flate cut
thin stone veneer saw (mighty stone saw) make cutting thin stone veneer flats and 90-degree corners quick, simple, low maintenance,and profitable. The unique v-structured cutting surface easily cuts split-face or natural finished sandstone, brick, limestone, and other hard stones up to 16" high and 2.5" thick. A single pass through the saw turns large stone pieces into thin stone veneer with unmatched consistency, efficiency, and reliability.

EM25-4 STONE VENEERING MACHINE • Belt Width: 300 mm & 300 mm • Working Width: 300 mm • Working Height: 50 - 300 mm • Double 45 Degree Conveyor Belts • Number Of Heads: 4 • Disc Diameter *Optional: 1000 mm - 900 mm - 800 mm - 600 mm • Head Motor Power *Optional: 3 x 22 kW, 1 x 7,5 kW • Belt Motor Power: 2 x 0,55 kW • Up-Down Motor Power: 0,55 kW • Belt Speed: 3- 5,5 mt / min • Machine Dimensions ( W / L / H ) : 2420 / 6880 / 2180 mm

Portable stone ,ceramic cutting machine
This machine mainly used to cut granite ,marble ,quartz stone and porcelian ceramic tile ,it adopt fast connection high precision guide rail to ensure the cutting precision and easy cut ,At the bottom of the guide rail have suckers to adsorbed on the slabs to make sure the stability when cutting.
The cutting blade can do 45 degree tilt for 45 degree edge chamfer cutting.
Main motor：1800W big power single phase motor.
Main motor rotation speed:8000RPM
Cutting thickness:60mm
Guide rail length:1350mm per one
Cutting blade size:5-6 inch

MITER SAW FOR 45 DEGREE CUTTING MSA
MITER SAW FOR THE PROFESSIONAL TILTED CUTTING AT 45 DEGREES
Professional stone saw for tilted cuts designed to work slabs "face down", it allows to perform perfect 45 degree cutting even on uncalibrated slabs. No width limitation of the slab to process; even the most narrow strips can be machined thanks to the special pneumatic pistons blocking the stone. The maximum cutting precision is guaranteed by the head travel on linear guides fitted with recirculating ball slides and by the position of the blade cutting from bottom upwards.
ADVANTAGES
MSA professional miter saw for tilted cuts:
Steel frame with hot-dip galvanizing treatment for maximum resistance to wear and rust;
Worktable made of anti-scratch plastic material slats;
Available in two models: useful cut 3300mm or 3700mm;
Maximum cutting precision is guaranteed by the head travelling on linear guides fitted with recirculating ball slides automatically lubricated;
10 pneumatic pistons and 3 slab stops to secure even the smallest workpieces in place during machining;
Pneumatic pop-up slab stops to cut thin ceramic and sintered material slabs.

Accessories
Manual lifting head “Z“ Axis with hand wheel.
Water recirculation pump.
Lifting hand.
Supporting steel table.
Lateral and orthogonal rollaway back stops.
Optionals
Idle roller table (front or back).
Angle square kit.
“X” axis movement with hand wheel.
Nr. 2 wheels for moving the machine.

FARNESE AUSTRALIA recognises the high demand from consumers for elegant stone features and the Stone Industry's need to make clean, quick and accurate mitres to meet this demand. The MITRE SAW simply and speedily cuts accurate mitres for a wide range of materials including engineered stone, granite, marble and porcelain of thickness ranging from 8 to 40mm.
Accuracy is the key when cutting mitres:
The more accurate the cut, the better the result. With the Mitre Saw Excel, an accurate mitre cut is achieved each and every time due to the precise angle of the blade and the straight edge system which uses front edge stoppers to accurately position the material on the table. No measuring. No mistakes. Coupled with this, the pneumatic clamps flatten the material against the table so that it's always straight and always stays in place.
The Mitre Saw's reputation for accurate cuts is also due to the fact the material is loaded polished face down, thereby eliminating cutting errors that can arise due to small variations in material thickness along its length.
The smaller diameter continuous rim special purpose blade, together with the variable feed control, means that a range of material thicknesses and hardness can be accommodated with less chipping and less cut deflection. The result? Greater accuracy and a straighter, cleaner cut. No need for an experienced saw operator; the Mitre Saw is easy to use and with minimal training requirements and fast installation it can fit into any workshop and make your business more profitable.