Basalt Finishing, Profiling Machines in Turkey

The CUTJET-W3 is a straightforward 2D quality waterjet cutting system for cutting many
materials such as glass, marble, granite, metal. Due to high-pressure abrasive cutting and
being a cold process, problems such as burning, droplets, deformation caused by thermal
reasons will be prevented.

Our Marble Granite Chamfering Machine provides Serial Standard production.
Easy to operate and maintain and Use
The feature of our machine is that it chamfering from the bottom.
The polished part of the marble is put on the band as Next.
Our Face Polishing Machine is fully automatic
Belt movement is electronically speed controlled.
Our machine is produced as 6 + 2 8 + 2 10 + 2 12 + 2 14 + 2 standard according to the Granite and Marble Type.
The engine part of our machine is completely free of water and protected from water with inner and outer protective enclosures.
Back of Abrasive Seals protecting head bearings are heat and abrasion resistant Felts.
All heads on the machine work independently from each other.
If desired, heads can be disabled according to the process.
The polishing heads come and go automatically with the entrance of the stone and automatically close and go back when the stone leaves the swishh.
There are 1 caliber, 5 bottom chamfer, 6 face chamfer, 1 deburring and 1 dropper saw on our 12 + 2 machine.
Our machine PROCESSES a maximum of 1500 mm with a minimum 70/80 mm lower support Jib Mechanism.
The Bandwidth of our machine is 450.
Our machine is Front Control Panel Controlled.
Protection Panels for Lubrication Channels Abrasive Replacement Fully Open and Close with Shock Absorber Support.
Herringbone diamonds can be integrated into our machine according to special requests.

Granite rain grooving machine
Video Link : https://www.youtube.com/watch?v=UpFRcIr72ps

Turkey’s 100% domestic water jet cutting pump and machine brand.
Mavijet 3 Axis and 5 Axis water jet cutting machines are manufactured by our expert engineer and technician team with patented technology.

Waterjet cutting machines CNC with entegrated KMT or BHDT Pump
KMT or ALLFI cutting head
FAGOR CNC Control Unit,
Fagor servomotors, Digital sercos
CE certificate

Bridge Type CNC Waterjet Machine is manufactured as tri-axis, five-axis and six-axis Mavijet with its tough body structure are designed for being able to operate continiusly and sentitively which are being manufactured with the using of high-class and longlived materials.
Servo motor, linear sledge and vehicles, helical rack and pinions is used for providing a rapid and smooth axial movement. The linear slides and rails, helical rack and pinions in all systems are protected with automatic greasing pump in order to prevent rust and to continue sensibility.
The fact that Mavijet CNC Waterjet Machine avoids vibration on account of its resisting rigid construction, is the main factor behind its high cutting speed and precision. Its rigidity enables a cutting with a 0.01 mm sensitivity.

The CUTJET-W5 is a cutting bench used for cutting many materials such as glass, marble,
granite, metal, plexiglass. Due to high-pressure abrasive cutting and being a cold process,
problems such as burning, droplets, deformation caused by thermal reasons will be prevented.
The 5-axis cutting head provides our customers with high-quality cutting opportunities
between 0° and 60°.

12 HEAD CHAMFER
Our Marble Granite Chamfering Machine provides Serial Standard production.
Easy to operate and maintain and Use
The feature of our machine is that it chamfering from the bottom.
The polished part of the marble is put on the band as Next.
Our Face Polishing Machine is fully automatic
Belt movement is electronically speed controlled.
Our machine is produced as 6 + 2 8 + 2 10 + 2 12 + 2 14 + 2 standard according to the Granite and Marble Type.
The engine part of our machine is completely free of water and protected from water with inner and outer protective enclosures.
Back of Abrasive Seals protecting head bearings are heat and abrasion resistant Felts.
All heads on the machine work independently from each other.
If desired, heads can be disabled according to the process.
The polishing heads come and go automatically with the entrance of the stone and automatically close and go back when the stone leaves the swishh.
There are 1 caliber, 5 bottom chamfer, 6 face chamfer, 1 deburring and 1 dropper saw on our 12 + 2 machine.
Our machine PROCESSES a maximum of 1500 mm with a minimum 70/80 mm lower support Jib Mechanism.
The Bandwidth of our machine is 450mm.
Our machine is Front Control Panel Controlled.
Protection Panels for Lubrication Channels Abrasive Replacement Fully Open and Close with Shock Absorber Support.
Herringbone diamonds can be integrated into our machine according to special requests.

FEATURES L-3015 PLUS MACHINE SERIES
NET WORKING AREA 3000X1500X400 MM
CHASSIS TYPE SQUARE PROFILE IRON CHASSIS
SPINDLE MOTOR HITECO
SPINDLE MOTOR POWER 11 KW
SPINDLE CYCLE 24000/18000
SPEED CONTROL 2.2 / 5 KW.
DRIVE MOTORS SERVO / HYBRID / OPTIONAL
X / Y / C / B AXIS MECHANICAL LINEAR RAIL, HELICAL GEAR
Z AXIS MECHANICAL COMPONENTS LINEAR RAIL, SCREW SHAFT
CNC CONTROL SYSTEM SINTEC UNIT
TABLE TYPE GALVENIZ STAINLESS TABLE
PROGRAM SENSITIVITY 0.01 MM
COOLING SYSTEM AUTOMATIC WATER COOLING
PANO PROFESSIONAL INDUSTRIAL TYPE PANEL
TOOL HOLD TYPE ER25 / ER32
WORKING CODE SYSTEM STANDARD ISO G CODE
SAFETY SYSTEM ELECTRONIC SENSOR
CONTINUES FROM THE LOCATION IN CASE OF ELECTRIC FAILURE
ELECTRICAL EQUIPMENT AT CE NORMS
COMPACTION SYSTEM PYNOMATIC
TOOL CHANGE

Bridge Type 6 axis Waterjet Machine is manufactured as full integrated with dividing system 2.1 Nm servo motors
Servo motor, linear sledge and vehicles, helical rack and pinions is used for providing a rapid and smooth axial movement. The linear slides and rails, helical rack and pinions in all systems are protected with automatic greasing pump in order to prevent rust and to continue sensibility.

Our Marble Granite Chamfering Machine provides Serial Standard production.
Easy to operate and maintain and Use
The feature of our machine is that it chamfering from the bottom.
The polished part of the marble is put on the band as Next.
Our Face Polishing Machine is fully automatic
Belt movement is electronically speed controlled.
Our machine is produced as 6 + 2 8 + 2 10 + 2 12 + 2 14 + 2 standard according to the Granite and Marble Type.
The engine part of our machine is completely free of water and protected from water with inner and outer protective enclosures.
Back of Abrasive Seals protecting head bearings are heat and abrasion resistant Felts.
All heads on the machine work independently from each other.
If desired, heads can be disabled according to the process.
The polishing heads come and go automatically with the entrance of the stone and automatically close and go back when the stone leaves the swishh.
There are 1 caliber, 5 bottom chamfer, 6 face chamfer, 1 deburring and 1 dropper saw on our 12 + 2 machine.
Our machine PROCESSES a maximum of 1500 mm with a minimum 70/80 mm lower support Jib Mechanism.
The Bandwidth of our machine is 450 mm.
Our machine is Front Control Panel Controlled.
Protection Panels for Lubrication Channels Abrasive Replacement Fully Open and Close with Shock Absorber Support.
Herringbone diamonds can be integrated into our machine according to special requests.

EM10 - Bullnose Machine

• Belt Width: 700 mm
• Working Width: 700 mm
• Number Of Heads *Optional: 4
• Diameter Of Socket: 240 mm
• Working Thickness: 10 – 100 mm
• Head Motor Power: 7,5 kW
• Up-Down Motor Power: 0,55 kW
• Belt Motor Power: 0,75 kW
• Total Electric Power: 33 kW
• Belt Speed: 0 – 4,9 rpm / min
• Water Consumption: 120 lt / min
• Machine Dimesnsions ( W / L / H ): 1700 / 4200 / 2100 mm
https://ekizoglumakina.com/en/product/bullnose-machine-em10

Designed for the most accurate Bevel cutting by the Mavijet 5 axis cutting head is making our customers cutting jobs very easy from 100 up to optionally 450

EM13 - The Profiling Machine
• Belt Width: 500 mm
• Number Of Heads *Optional: 4
• Working Thickness: 10 – 100 mm
• Head Motor Power: 7,5 kW
• Belt Motor Power: 0,75 kW
• Total Electric Power: 31 kW
• Belt Speed: 0 – 4,9 m / min
• Diameter Of Socket: 240 – 300 mm
• Water Consumption: 120 Lt / min
• Machine Dimensions ( W / L / H ): 1500 / 4000 / 1800 mm
https://ekizoglumakina.com/en/product/profilling-machine-em13

Anchor system, hook channel and hole is the machine.
Makes 4 holes and 4 grooves in one operation.
It provides you maximum speed with conveyor system and PLC control.
The machine for those who race against time
It opens 4 holes and 4 chamfer channel in a sing operation
Performance Durations-- Average time
Opening Holes --5 sec
Opening Channels --2 sec
Transition to Other Operation--4 sec
Total Operation Time-- 11 sec

SPECIFICATIONS M-1020 MACHINE SERIES
NET WORKING AREA 2000X1000X300 MM
CHASSIS TYPE SQUARE PROFILE IRON CHASSIS 10MM
SPINDLE MOTOR HERTS / AREL
SPINDLE MOTOR POWER 2.2 / 5 KW.
SPINDLE CYCLE 24000/18000
SPEED CONTROL 2.2 / 5 KW.
DRIVE MOTORS HYBRID SERVO / SERVO / STEP
X AND Y AXIS MECHANICAL PARTS LINEAR RAIL, HELICAL CREMAYER GEAR
Z AXIS MECHANICAL COMPONENTS LINEAR RAIL, SCREW SHAFT
CNC CONTROL SYSTEM DSP PANEL / MACH3 / SİNTEC / ARTCEM
TABLE TYPE GALVENİZ STAINLESS TABLE
PROGRAM SENSITIVITY 0.01 MM
COOLING SYSTEM AUTOMATIC WATER COOLING
PANO PROFESSIONAL INDUSTRIAL TYPE PANEL
TOOL HOLD TYPE ER25 / ER32
WORKING CODE SYSTEM STANDARD ISO G CODE
SAFETY SYSTEM ELECTRONIC SENSOR
CONTINUES FROM THE LOCATION IN CASE OF ELECTRIC FAILURE
ELECTRICAL EQUIPMENT AT CE NORMS
COMPACTION SYSTEM PYNOMATIC

3 Axis CNC Waterjet can cut all kinds of materials existing in the nature up to 200 mm thickness with power generated by mixing pressurized water and abrasive sand. All materials cutting can be made with the same nozzle. Not only for thick but also for thin materials, it can realize 90 degrees corner, narrow angular and small radius precise cuttings.

the thrilling mosaic cutting machine of the age hard to find even on the second hand market
order now start counting your golden münze
precise cutting
1x1 cm 1,5x1,5 cm 2x2cm 2,3x2,3cm all american sizes available
custom design assebly molds
cutting molds with availibity of cutting triangle ; octagon and many other custom shapes

3D 5 Axis CNC Waterjet is designed by our engineers to make highly precise 0-120 degrees angular cuttings.Thanks to rigid structure, not being affected by deflector force of high pressure coil, can realize 3D cuttings in 0.02 mm accuracy.5 axis head can rotate +/- 360 degrees.

Description
ÖZELLİKLER EKO 912 SERİSİ
NET ÇALIŞMA ALANI 1200X800X200 MM
ŞASE TİPİ KARE PROFİL DEMİR ŞASE 10MM
SPİNDLE MOTOR HERTS/AREL
SPİNDLE MOTOR GÜCÜ 2.2/5.5 KW.
SPİNDLE DEVRİ 24000/18000
HIZ KONTROL 2.2/5 KW.
HAREKET MOTORLARI HYBRİD SERVO / STEP
X/Y/C/B EKSENİ MEKANİK LİNEER RAY
Z EKSENİ MEKANİK AKSAM LİNEER RAY, VİDALİ MİL
CNC KONTROL SİSTEMİ DSP PANEL / MACH3
TABLA TİPİ GALVANİZ PASLANMAZ TABLA
PROGRAM HASSASİYETİ 0,01 MM
SOĞUTMA SİSTEMİ OTOMATİK SU SOĞUTMA
PANO PROFESYONEL ENDÜSTRİYEL TİP PANO
TAKIM TUTMA TİPİ ER25/ER20
ÇALIŞMA KOD SİSTEMİ STANDART ISO G KODU
EMNİYET SİSTEMİ ELEKTRONİK SENSÖR
ELEKTRİK KESİNTİSİNDE KALDIĞI YERDEN DEVAM EDER
ELEKTRİK DONANIMI CE NORMLARINDA
SIKIŞTIRMA SİSTEMİ PİNOMATİK

For detailed information about the product, you can download the relevant documents.

CNC MACHINING CENTER
GENERAL DESCRIPTION:
NC4-320 4 axes is a multifunctional working centre to process marble, granite and compound stone designed also for complex processing in short time and high quality. NC4-320 has been specially designed to ensure higher production capacity as well as the largest flexibility thanks to the very high working and displacement speed and the wide gamut of possible geometries,which allow any kind of processing ( shaping, profiling, milling, chamfering, drilling...)on marble, granite and compound stone slabs without the intervention of the operator, following a pre-set program. The machine features a mobile bridge structure, engineered using the state-of-the-art techniques of computer-assisted design, which forms a sole assembly with the uprights fixed to the based onto which the pieceholding table is applied.
AXES MOVEMENT:
The axes move by re-circulating ball screw at 60 m/min with accelerations which permit to reach the maximum speed in very short time. An automatic device to lubricate the guides and the screws grants high reliability over the time of every moving part.
The rapid displacements of the bridge along the shoulders are performed at a speed of 40 meters per minute; this make it possible to have faster work cycles, as all idle times for non-operative movements are absolutely negligible.
THE SPINDLE UNIT:
The tempered and rectified steel guides for the displacement of the spindle holding saddle (x axis) are machined onto the normalized, electrowelded steel bridge, suitably dimensioned and ribbed. The whole sliding system is protected in order to avoid any possible contamination between the processing water and lubricating oil. The spindle holding saddle moving on recirculating roller slides.
In order to obtain rapid displacement up to 40 meters per minute, which accelerates the work cycles, the movement of the spindle-holding saddle is provided by a fixed high precision rectified screw and a mobile ball bearing preharced lead nut linked directly to a digital SIMENS servo motor.
The electro-spindle adopted for this work centre is manufactured by the most important european producer of these components; it is a powerfull unit (12kw) and can attain very high rotationspeed (max 11.000 rpm) in order to use milling tools with reduced diameters and therefore, providing extremely pricise processing. The stator and the rotor are housed within the casing; the whole assembly is cooled and stabilized by means of a thermal sensor to increase its reliability. The tool cooling water and the cone cleaning air pass through the spindle at a flow rate of 60lt/min. Spindle vertical travel of same 400 mm which allows to also rough-sahpe tick billets.
CONTROL UNIT:
The NC4-320 is equipped with a latest technology continuous numerical control unit (CNC) SIMENS sinumeric of the latest generation, with digital control on PC architecture.
STRUCTURE:
The support structure of the NC4-320 is composed of a rugged closed-type structure fabricated from a single pieces of normalized welded steel, so as to quaranty the maximum rigidity, thereby providing extremely pricise processing
The bridge moves along the shoulders of the main structure, onto which the tempered and rectified steel guides are machined.
The bridge movement along the shoulders is by a system of two recirculating ball-bearing screws with precharged lead nuts, each one acting on one side of the bridge.
This solution allows to have perfect control and absolute precision oof movement and positioning. Traction is garantied by two digital servo motors, each one acting on one screw; the perfect synchronism of the two screw is constantly driven by SIMENS numerical control installed on the machine.( Gantry drive system )
The NC4-320 numerical work centre has a mobile bridge along the Y axes; this solution makes the work area completely open and accessible, which facilitates loading and unloading of work-pieces even when lifting equipment is required.
Vacuum circuit with frontal control, easily accessible to the operator.
THE WORK TABLE
The machine’s base is made up of an extremely rigid structure upon which is placed an aluminium worktable rectified to grand maximum flatness of the work area. Aluminium work table provided with grooves for mechanical fastening of vacuum pads, to ensure that, the work pieces are tightly locked in place even during heavy grinding operations 22 position line tool store positioned on the two internal sides of the machine.
THE FOURTH “C” AXES:
Among the range of accessories, it is also available a unit that allows to use tools with horizontal axes.
This unit is fixed to the spindle by means of ISO 40 coupling,as any other tool; it can continuously rotate 360 around the , “C” vertical axes, which is numerically controlled and can be locked in any position to perform retilinear cuts in all directions.
It is a continuous rotating fourth axes “C” which makes it possible to use cutting units with vertical disc to perform rectilinear cuts, or convex disc for corvilinear cuts, or 45 adjustable disc to perform inclined cut
STANDARD SUPPLY
Manuel for use and maintanance.
20 pcs. BT 40 tool stainless steel holder cones ( ½ gas )
20 pcs. Adapter for wheel cutters
20 pcs. Pullstad bolds.
4 pcs. Ø160 mm suction cups.
4 pcs. Ø 100 mm suction cups.
4 pcs. Ø 80 mm suction cups.
6 pcs. Retractable positioning reference supports.
2 pcs. Pneumatic vice.
2 pcs. Retractable suction cups Ø 100 mm.
Tool box.
Spindle motor chiller
Vacuum pump
Water filtration device.
Air filtration devices for 5 microns
Electric box air-conditioning.
Electronic Siemens handwheel.
2 pcs. Water pumps.

OZKKM 5 Axis / HYDRA Waterjet Machine

Multi Purpose Workshop type 4 axis Machine - Cutting, Profiling

The CUTJET-W5 is a cutting bench used for cutting many materials such as glass, marble,
granite, metal, plexiglass. Due to high-pressure abrasive cutting and being a cold process,
problems such as burning, droplets, deformation caused by thermal reasons will be prevented.
The 5-axis cutting head provides our customers with high-quality cutting opportunities
between 0° and 60°.

EM13 - The Profiling Machine
• Belt Width: 500 mm
• Number Of Heads *Optional: 4
• Working Thickness: 10 – 100 mm
• Head Motor Power: 7,5 kW
• Belt Motor Power: 0,75 kW
• Total Electric Power: 31 kW
• Belt Speed: 0 – 4,9 m / min
• Diameter Of Socket: 240 – 300 mm
• Water Consumption: 120 Lt / min
• Machine Dimensions ( W / L / H ): 1500 / 4000 / 1800 mm
https://ekizoglumakina.com/en/product/profilling-machine-em13

CNC MACHINING CENTER
GENERAL DESCRIPTION:
NC4-320 4 axes is a multifunctional working centre to process marble, granite and compound stone designed also for complex processing in short time and high quality. NC4-320 has been specially designed to ensure higher production capacity as well as the largest flexibility thanks to the very high working and displacement speed and the wide gamut of possible geometries,which allow any kind of processing ( shaping, profiling, milling, chamfering, drilling...)on marble, granite and compound stone slabs without the intervention of the operator, following a pre-set program. The machine features a mobile bridge structure, engineered using the state-of-the-art techniques of computer-assisted design, which forms a sole assembly with the uprights fixed to the based onto which the pieceholding table is applied.
AXES MOVEMENT:
The axes move by re-circulating ball screw at 60 m/min with accelerations which permit to reach the maximum speed in very short time. An automatic device to lubricate the guides and the screws grants high reliability over the time of every moving part.
The rapid displacements of the bridge along the shoulders are performed at a speed of 40 meters per minute; this make it possible to have faster work cycles, as all idle times for non-operative movements are absolutely negligible.
THE SPINDLE UNIT:
The tempered and rectified steel guides for the displacement of the spindle holding saddle (x axis) are machined onto the normalized, electrowelded steel bridge, suitably dimensioned and ribbed. The whole sliding system is protected in order to avoid any possible contamination between the processing water and lubricating oil. The spindle holding saddle moving on recirculating roller slides.
In order to obtain rapid displacement up to 40 meters per minute, which accelerates the work cycles, the movement of the spindle-holding saddle is provided by a fixed high precision rectified screw and a mobile ball bearing preharced lead nut linked directly to a digital SIMENS servo motor.
The electro-spindle adopted for this work centre is manufactured by the most important european producer of these components; it is a powerfull unit (12kw) and can attain very high rotationspeed (max 11.000 rpm) in order to use milling tools with reduced diameters and therefore, providing extremely pricise processing. The stator and the rotor are housed within the casing; the whole assembly is cooled and stabilized by means of a thermal sensor to increase its reliability. The tool cooling water and the cone cleaning air pass through the spindle at a flow rate of 60lt/min. Spindle vertical travel of same 400 mm which allows to also rough-sahpe tick billets.
CONTROL UNIT:
The NC4-320 is equipped with a latest technology continuous numerical control unit (CNC) SIMENS sinumeric of the latest generation, with digital control on PC architecture.
STRUCTURE:
The support structure of the NC4-320 is composed of a rugged closed-type structure fabricated from a single pieces of normalized welded steel, so as to quaranty the maximum rigidity, thereby providing extremely pricise processing
The bridge moves along the shoulders of the main structure, onto which the tempered and rectified steel guides are machined.
The bridge movement along the shoulders is by a system of two recirculating ball-bearing screws with precharged lead nuts, each one acting on one side of the bridge.
This solution allows to have perfect control and absolute precision oof movement and positioning. Traction is garantied by two digital servo motors, each one acting on one screw; the perfect synchronism of the two screw is constantly driven by SIMENS numerical control installed on the machine.( Gantry drive system )
The NC4-320 numerical work centre has a mobile bridge along the Y axes; this solution makes the work area completely open and accessible, which facilitates loading and unloading of work-pieces even when lifting equipment is required.
Vacuum circuit with frontal control, easily accessible to the operator.
THE WORK TABLE
The machine’s base is made up of an extremely rigid structure upon which is placed an aluminium worktable rectified to grand maximum flatness of the work area. Aluminium work table provided with grooves for mechanical fastening of vacuum pads, to ensure that, the work pieces are tightly locked in place even during heavy grinding operations 22 position line tool store positioned on the two internal sides of the machine.
THE FOURTH “C” AXES:
Among the range of accessories, it is also available a unit that allows to use tools with horizontal axes.
This unit is fixed to the spindle by means of ISO 40 coupling,as any other tool; it can continuously rotate 360 around the , “C” vertical axes, which is numerically controlled and can be locked in any position to perform retilinear cuts in all directions.
It is a continuous rotating fourth axes “C” which makes it possible to use cutting units with vertical disc to perform rectilinear cuts, or convex disc for corvilinear cuts, or 45 adjustable disc to perform inclined cut
STANDARD SUPPLY
Manuel for use and maintanance.
20 pcs. BT 40 tool stainless steel holder cones ( ½ gas )
20 pcs. Adapter for wheel cutters
20 pcs. Pullstad bolds.
4 pcs. Ø160 mm suction cups.
4 pcs. Ø 100 mm suction cups.
4 pcs. Ø 80 mm suction cups.
6 pcs. Retractable positioning reference supports.
2 pcs. Pneumatic vice.
2 pcs. Retractable suction cups Ø 100 mm.
Tool box.
Spindle motor chiller
Vacuum pump
Water filtration device.
Air filtration devices for 5 microns
Electric box air-conditioning.
Electronic Siemens handwheel.
2 pcs. Water pumps.