Basalt Factory Machines in Spain

Ares oven by Xilex dries water instantly both inside and on the surface of the stone slabs. This oven is intended for drying process on natural stone (marble and granite), artificial stone (quartz and cristobalite) and porcelain tile.
Unlike conventional kilns, Ares effectively removes moisture by drying all cracks and holes so that the material is prepared for optimal filtering and resin adhesion in the next step on the production line.
In addition, Ares is an instant oven since it performs an effective drying in just 2-3 minutes, a very short time in comparing to the drying of 30-60 minutes that conventional ovens require. The instant drying allows a quick manipulation of the slabs so the productivity increases up to 20% depending on the process.
Ares is installed without the typical foundations of conventional systems, does not require the additional use of metal trays and does not require high maintenance costs, so the purchase and installation of the Ares oven by Xilex is 40% cheaper than the acquisition of a conventional system.
Great energy savings in drying of marble and granite
The great profitability of Ares is related, in addition to optimizing time, with a significant decrease in power consumption. Ares efficiency represents a 15% saving in energy expenditure compared to conventional drying systems. This decrease in energy consumption is mainly due to three factors:
Instant start with 100% efficiency. This is a great added value compared to conventional systems, which require one hour of preheating.
Adaptation of power to the material. Ares automatically adapts to the material’s drying needs, adjusting the power required for each piece. Conventional lines, on the other hand, perform linear power consumption.
Power on when detection of slabs. Ares only lights up when it detects the presence of slabs, unlike conventional lines that remain on whether there are slabs or not.
Quick and easy adaptation of the Ares oven to the production line
Ares oven is easily installed on the production line and adapts to any transport system without additional investment thanks to its practical size (2500mm x 2500mm), compared to a conventional accumulator (7000x2500x6000mm).
It is also important to note that Ares allows slabs to be dried directly from the block cutter or multiwire since the machine can be installed on the existing transport line without the need for any works or foundations, furthermore, its installation does not even require stopping production.
For all these reasons, the Ares oven by Xilex is a technology for all companies that work with marble and granite and seek a definitive solution to moisture problems to improve processes, increase production and offer a higher quality product to their customers.

The standardization of single girder cranes makes this configuration optimizes the use of space, together with a minimum weight.

Our MILLENNIUM range is designed for those who are willing to stay one step ahead of the world market and demand total reliability in a CNC machine.
Precision, productivity, efficiency, durability, design and maximum quality worldwide for each of its components, being the most valued equipment over the years.
The first CNC Intelligent equipment was presented for the first time at the ExpoPiedra Madrid 2000-2002 fair under the name of Millennium. After more than 15 years of development and continuous improvement, the new MILLENNIUM range represents the most intelligent machines on the market, Intelligent Performance, being REFERENCES IN THE INTERNATIONAL MARKET.
MILLENNIUM MONOBLOCK CNC 5X
The MILLENNIUM CNC 5-Axis Monoblock Cutter, the top machine in our range, is the reference in the market with more than 250 units installed throughout the world.

NVM-1000 Manual Cutter
Space required for installation: 6000 X 3000M
Corte útil por detrás del disco: 1000mm Useful cut behind the album: 1000mm
Potencia del motor: 10 CV Engine power: 10 hp
Potencia de elevación del cabezal: 1 CV Power Lifting Head: 1 HP
Elevación útil del cabezal: 300mm Lifting head useful: 300mm
Corte longitudinal: 3500 mm Longitudinal: 3500 mm
Corte inglete Miter cut
Carro 2500 X 1300 mm 2500 X 1300 mm Car
Guías, ruegas, engranajes y soportes protegidos contra en agua Guides, beg, gears and protected in water supports
Galga de 2500mm de larga 2500mm long gauge
5 pletinas que hacen función de tope para agalgar con tornillos inoxidables regulables 5 plates that make a stop for agalgar function with adjustable stainless steel screws

108 003 140 Charge Tables Jib Arm U Type Container Loader

Kronos is the Xilex machine that allows total control of the filtering and adhesión process to obtain top quality finishes. It is an oven for epoxy, polyester and polyurethane (PUR) resin curing that accelerates the activation and consolidation of chemical properties in marbles, granites and other more delicate types of natural stone such as onyx or alabaster.
Kronos oven differs from conventional machines in that it performs greater filtration and adhesion of resins, and it allows to produce controlled effects on the surface finish (brightness, light and dark tones, etc.) with a production of up to 30 tables at hour.
Also, Kronos by Xilex eliminates waiting times of 24h-48h-72h since natural stone can be polished directly after only 45 minutes. In this way, production lines can perform reinforcement, finishing and continuous polishing, which translates into a 30% increase in productivity and a significant reduction in delivery times of the final product.
Maximum quality and control of the marble and granite finish
Kronos allows filtering control and perfect adhesion to achieve the best slabs quality and avoid breakage in the final material. Also, the good filtering of Kronos in its uniform process improves the performance of the resins and allows to obtain the desired surface effects on the product.
The resin hardening machine, Kronos, can easily adapt to conventional production lines as it fits to the standard size of the transport tables. In this way, companies in the marble, granite and natural stone sector that want to improve the finish of their materials and optimize processes just have to make a simple adaptation of their production lines.
Productivity increase and cost savings with Kronos
Processing with Kronos oven by Xilex allows a fast activation of catalysis of resins, achieving significant savings and a 30% increase in productivity:
Eliminates waiting time of 24-48-72h: after hardening, in 45 minutes, polishing can be performed.
Increase of production in the number of resin slabs.
Reduction of resin consumption up to 20%.
Energy savings of up to 40%.
Space optimization: reduction of the trays necessary for material processing and elimination of intermediate warehouses before polishing.

The double girder configuration, thanks to the calculations system used, has an optimized weight, reducing loads on the structure, together with a greater stability when handling large loads.

MULTIWIRE N6860/60 TECHNICAL SHEET
The new Diamond wire cutting machine NDF 6870/60 is a multi-wire machine designed to produce boards and plates of varying thickness from the large blocks of marble and natural stone. This new unit represents the most modern technology in what refers to the primary sawing of the stone blocks, becoming the alternative to the traditionally used sawing methods, since it improves the production capacity quantitatively, efficiently taking advantage of the energy resources needed to the production of materials and significantly reducing the production costs of the cutting phase.

The multiple diamond wire cutter is a machine that stands out for its efficiency and high productivity, designed to obtain high yields, which is characterized by its great robustness, thanks to its particular design that forms a compact, balanced and balanced set where all movements are concentrated, and its proven reliability and that of the elements that compose it, being all designed to withstand the toughest working conditions.

The main structure of the machine is basically composed of two sturdy columns formed by two steel-welded steel structures, connected between them by an upper crossbar. On both columns the structure of the main frame that joins the two trolleycarriages is mounted, which move vertically supported on both columns on linear guides with linear roller recirculation skates and actuated by a pair of spindles rolled with recirculating nuts balls, synchronized and operated by two motor-reducers with independent servo motors for the ascent / descent of the threads with a smooth and precise movement, located in the upper part of both columns, the entire guide assembly is perfectly protected by PVC bellows . The servomotors are synchronized by software in the vertical movements that ensure smooth cutting, low consumption and maximum precision and avoid the slacks and problems of the central motorization with transmission and forwarding.

The Ø1800 drive drum is formed by a single multi-channel pulley with grooves and connected to the main motor by a pulley and timing belt transmission. The threads are manually positioned according to the desired thickness supported by one side of the machine on the drive drum, and in turn are tensioned from the opposite end by autonomous pulleys. The diamond wires are also guided by two multichannel drums that help to significantly reduce the arrow produced by them. From the opposite end to the driving drum, the diamond wires are supported by the set of idle pulleys, designed with a particular pivoting extraction system, which allows reducing maintenance times significantly.

Once the wires are located, these are adjusted with the active tensioning device that acts individually on each of the tensioning pulleys, independently ensuring that each of the threads has the same tension regardless of the minimum differences in length between each of the threads that are installed in the machine. The tensioning system manages to increase the useful life of the wires and therefore the profitability of the machine

The whole machine is characterized by the robustness and reliability of the elements that compose, being all designed to withstand the toughest working conditions, and in this aspect it is precisely where we can provide all the experience accumulated over the years we have been designing and manufacturing machinery for this sector.
Notable features
Reduced and optimized energy consumption.
Mechanical robustness and absence of vibrations.
Active and independent tensioning system, which increases the useful life of the threads, increasing profitability and ensuring optimum surface finishes.
Innovative pulley design, with pivoting extraction system that reduces maintenance times.
Full range of cutting thicknesses, thanks to its particular design of pulley packages and combination of grooves, without penalizing the life of the diamond wire.
Excellent precision and flatness of cut, through its particular system of guidance by linear skates and its rigid bearing structure.
Easy and convenient access to the inside of the machine, thus facilitating the work of changing threads and their maintenance.
Helical spindles with large diameter balls in vertical movement for smooth or precise movement.
Servomotors synchronized by software in vertical movements that ensure smooth cutting, low power consumption, maximum precision and avoid gaps and problems of central motorization with transmission and forwarding.
Up to 60 wires with various possibilities for the combination of cutting thicknesses.

Strong points
The multiple diamond wire cutter is a multi-wire cutter designed to produce slabs, boards and slabs of varying thickness from the large blocks of marble and natural stone. Traditionally in the factories of transformation of the granite, the cut of blocks is being made of the size of the same with looms when the blocks are of big dimensions, or with bridge cutters of big diamond discs in the workshops of stonework when cutting semiblocks.
The biggest aspect to note is that the multi-wire cutter, for an equivalent capacity, the effective energy consumption, is lower compared to any of the methods used. This translates into significant energy savings both in the implementation, as in production costs.
This difference in the equivalent energy saving is mainly due to the difference in sawing technology, the multi-wire cutter only uses up to 60 loops of diamond wire and water during this process by cutting continuously. These diamond wires are basically formed by a steel cable covered by diamond rings along the cable, the cutting effect on the stone block to obtain the slabs and boards is produced by the effect of the continuous drag movement of the wires at a linear speed of about 38 meters / sc. combined with the rotation of the rings, producing a very high cutting power, differentiated effect with respect to the large traditional looms where the cutting process can be defined as the effect of a reciprocating saw, formed by a frame that houses about 100-130 steel strips in contact with the stone blocks at the same time moving c incombination with the rain of abrasive mixture of water, steel shot and lime, which produces the same amount of incisions in the stone block that amount of strapping
In summary, the coefficient resulting from the equivalent energy consumption in Kw / m2 of a multi-wire cutter compared to the loom is greater than 50% savings, even considering that the total installed power of a multi-wire cutter is greater than that of a traditional loom.
The Multiple Diamond Wire Cutter is the alternative to the primary sawing methods currently used, improving the production capacity quantitatively, efficiently taking advantage of the energy resources necessary for the production of materials and significantly reducing waste produced during the cutting phase.
Comparatively, the advantages of using this new technology applied to the multiwire cutter are obvious. The multi-wire cutter can cut any type of stone material in front of looms that only cut granites or marble, but these are two different models and that use different tools, the looms are only profitable when cutting 2-3 cm sheets of thickness, but its biggest disadvantage is in the energy consumption and the very high production of solid waste, since the water used is recovered in all cases, this waste apart from assuming a higher purification cost, presents a problem of environmental pollution in case of the looms because it contains iron, and the lime that alters the acidity of the waters, in addition to the moment it is not possible to separate or recover at this stage of the process. There is an important difference compared to traditional cutters, which is based on the cutting height, with a disc we can cut 1.50 meters in front of the diamond wire that any commercial block can cut, apart from the great productive difference that exists
The water treatment and purification process for this new process is therefore more economical and less complex.
It is also worth noting that the water needs, while being similar, with respect to the traditional loom, the diamond wire cutting practically cancels the need to wash the load after sawing, this being much less demanding and both the needs and Water losses during the cutting process are lower.
Another aspect to note is that the multi-wire cutter, for an equivalent capacity, the effective energy consumption, is lower compared to any of the methods used. This translates into significant energy savings both in the implementation, as in production costs
With respect to consumables, say that in the multi-thread cutter there is only one; the diamond wire, small volume, easy storage and simple supply. The costs derived from storage, stock programming and handling, are also lower with respect to strapping, shot and lime, necessary for the traditional loom.
In reference to the costs of implementation, the simplicity and the consequent lower cost of civil works stand out in the first place, while in the loom the necessary work constitutes an indispensable part of it, in the multi-wire cutter, this becomes a mere support of it. In addition, in the case of renewal or replacement of the machine, the loom forces the new implantation to be exactly the same model as the previous one, while in the case of the multi-threaded cutter there is a high degree of possibilities of being able to make an adaptation of the existing civil works. In any important case, that is, the space occupied by the multiwire is less.
The simplicity of the multiwire is significantly greater, both in installation, use and handling, as well as in maintenance, both mechanically and electrically. It is important to note that the NDF-6870/60 multi-wire cutter does not use the common solution for vertical movement consisting of a central motor with reducer, transmissions and angular forwarding. This is replaced by two independent and electronically synchronized servomotors without coupling between them. This solution, in effect, cancels the inconveniences of the classic mechanical transmissions, the clearances and possible breaks due to wear and fatigue, and also allows us greater flexibility in the movements to be carried out. In this regard, it should be noted that the system is capable of working atspeeds as slow as one millimetre per minute, as at the fastest of almost one meter per minute, all without loss of power or precision in movement.
As a practical effect, the NDF-6870/60 cutter is the fastest machine on the market capable of performing a vertical ascent movement against any contingency, avoiding the undesirable marks of diamond wire in the stone.
The surface of the final product serrated with the diamond wire, in addition to the fact that it does not need to be practically washed, much less the use of harmful acids or chemicals and dangerous handling, offers the important advantage that its surface state can be assimilated to a certain jaded In the event that the material must be subsequently polished, a certain reduction in the costs associated with the abrasives used in the polishing process and the consequent reduction in production times should be noted.
The high speed of the multiwire cutter will also allow new users of this technology to schedule production with a lower advance and greater flexibility than the loom, even allowing partially cutting a block and reserving the rest of it for another more appropriate time.
The flexibility of production is also given by the clearly lower staffing needs. The preparation of the saw in a thread cutter for a cut, consumes less than half the time and less than half of human resources than a traditional strapping loom
With this cutting unit it is intended to integrate the fully automated operation of the primary sawing work of the stone blocks, with the minimum human intervention and therefore a significant reduction in the manoeuvres of product handling, regularization and optimization of the work processes, the increase of the productive capacity thanks to the reduction of the cycle times and the efficient use of the dead times, the reduction of the energy consumption and the production of the waste during the cutting process, and finally the reduction of the associated risks for the personnel involved in the work of manipulation and mechanization of the materials throughout each working day

Why should our cutter be bought?
The use of diamond wire in the primary sawing work has been used in the sector for not many years, and said wire is applied on known machines, normally formed by two pulleys on which a wire is installed forming a closed loop with which the cuts are made on the stone blocks.

In recent years, machines have begun to be used that use several diamond threads, which are mounted on multi-channel drums or formed by several pulleys, on which several threads are mounted in order to make several cuts at the same time on the stone blocks, thus obtaining significant productions.

The machines used up to now present different technical problems when performing the correct tensioning and control of the thread loops, in addition to another more significant one that lies in the possibility of varying in a simple way the position of the pairs of wires in order to obtain different thicknesses or vary them in the production of boards.

Taking these disadvantages into consideration, the N.6860/60 cutter stands out for its simplicity in the individual tensioning device of the tension wheels, and at the same time the variation of processing thicknesses in the slabs and boards to be cut has been simplified in a simple and easy way.

NODOSAFER offers its customers in addition to all the features intrinsic to any thread machine, such important improvements as:

Architecture based on a robust and compensated structure to avoid vibrations.
Maximum protection against the penetration of water and dust in the most sensitive parts.
Large diameter helical ball screws in the vertical movement for a smooth and precise displacement.
Linear roller recirculation guides in the columns to guarantee the absolute verticality of the cut.
Servo motors synchronized by software in the vertical movements that ensure smoothness in the cutting, low consumption, maximum precision and avoid the gaps and problems of the central motorization with transmission and forwarding.
Basic large diameter drive drum mechanism that prolongs the life of the thread.
Automatic tensioning device by independent pulleys of each of the threads, with position, arrow and tension control of each of the threads.
Automatic and progressive decrease of speed in case of excessive arrow in the thread.
Detection of thread breakage and controlled stop (rapid braking and maximum speed climb)
Controlled emergency stop to avoid marks on the cut block.
Possibility to resume a cut in automatic or semi-automatic mode.
Wide range of devices and program functions for operator and machine safety.
Motorized trolley with optional position control.
Operator panel in color with great ease of use and multiple configuration possibilities.
Compact electrical panel with the latest technologies.
High power main motor driven by inverter.
Button pad for movements in manual mode.
Automatic greasing.
Security
NODOSAFER machines are protected and provide a safety lock around their entire perimeter in accordance with CE safety standards
Load block trolleys
The machine has 2 motorized block trolleys fitted as standard.

The MILLENNIUM CNC 5X Indianapolis cutter is a new concept of cutter designed by De La Cruz Stone Technology. Our team of engineers and designers have worked tirelessly for years to create and refine this concept that will allow fabricators to customize machines to meet all of their future cutting needs.
This machine was designed during the creation of our top-notch MILLENNIUM CNC 5X Monoblock cutter and shares all of its top-tier features. This, together with the possibility of new modifications, makes the MILLENNIUM CNC 5X Indianapolis the ideal cutter for many manufacturers.

Automatic strip polisher used to polish rough material, granite and marble surfaces.
There is a first zone which incorporates the gauging headstocks. The second one is provided with the polishing headstocks which have a swing movement in order to guarantee a good finish result.
This machine enjoys an accurate design. On the frontal part there is a strip with transparent components as well as the headstocks and strip controls so that the work which is being done can be comfortably controlled and seen.
Different models depending on the amount of headstocks and the material minimum width to be worked with. Its features can be modified according to every moments’ needs.

Pantographs Sculpture Carving Machine
Ideal machine for making funeral attributes or advertising boards

The wide variety of GR CP machines allow us to work with discs from 350 mm to 800 mm. These machines are the perfect option to cut marble, granite, silestone, dekton and many more. They can also cut mitres, make moulding and make several different shapes.
All the machines GR CP are made to increase production, and besides they make to the marble-workers their work easier and faster.
Optional Accessories:
- Laser positioning system
- Table with rotatory system from 0o to 360o
- Speed controller for axles X, Y and Z
- Copying system for making mouldings
- Head installed for cutting mitres
- Main engine frequency controller
- Lineal cuts
- Winch to cut shapes like ovals, circles …

Automatic cross cutting line with multiple heads for accurate and squared cutting in each end of piece

GH underslung cranes are the choice when very big spans are required, or no traditional crane runways are available.
They can be manufactured with cantilevers to access difficult points, and even can be designed to transfer materials between halls.

The cutting line N.2990/2200-5+7C counts with:

1 Intermediate motorized plastic rollers table, model N.2274.
1 longitudinal cutter with 5 cutting heads ø 600 and mobile bridge, model N.8000-L-5C.
1 transverse cutter with 7 cutting heads ø 600 and mobile bridge, model N.8000-L-7C.
2 motorized band cutting tables, model N.2304.
1 table with stone sheet selection stops, N. 2590.
1 double displacement table with motorized rollers, model N.2585.
1 motorized band table for material output, model N.2426.
CUTTING LINES N2990/2200 5 + 7 HEADS TECHNICAL SHEET
Our cutting line N.2990/2200-5+7C has been designed aiming maximum production capacity with minimum labour force, as well as the absolute reliability of all its parts.

The production line overall dimensions have been adjusted to the customer needs, following his criteria about the produced pieces dimensions and the final products obtained.

The whole line features better robustness and reliability in all its subassemblies, being them all designed to support the hardest working conditions. This is one of the most relevant aspects where we can offer our long time experience in designing and manufacturing stone processing machines for this sector.

One of the great advantages of the machines integrating this production line is that all the designs are already tested solutions. They only differ from our standard machines in their overall dimensions, but not in all incorporated components.

With the automatic loading trolley NDF-1289-P/V (optional), the longitudinal cutter is fed with material from a stacker. Panels are removed using suction cups connected to a vacuum pump that tilt and place them in a horizontal position, ready to move to the cutting unit. Panels from the horizontal stacker are placed waiting to enter in the production line in such a way that the following panels maintain the alignment being unnecessary to adjust the cutter starting point.

The intermediate rollers table not only joins the feeding trolley and the longitudinal cutter but also acts as an intermediate storage so that the cutting unit stop times are very low.

The 5 heads longitudinal cutter N.8000-L-5C over rolling bridge and the 7 heads transverse cutter N.8000-T-7C are equipped with the latest technology, both in their mechanical design and in their electronics. It is worth mentioning the use of a high precision and stiffness linear guide system with linear recirculating ball bearing unit by the gripper cutting head bridge during the cutting works. The bridge is supported by two beams, being parallel to the cutting table the first and perpendicular, the second.

The sliding disc holder cutting heads also move vertically guided by a linear recirculating ball bearing unit and operated by a laminated ball screw with recirculating ball screw nut in order to achieve a quick and precise positioning and being all perfectly protected by PVC bellows. The gripper cutting heads have translation movement thanks to a gear motor controlled by a frequency inverter and positioning magnetic scale in the X axis and cutting head operated by a ball screw and an electric gear motor for vertical positioning in the Z axis. The cutting heads positioning is simultaneous thanks to their independent inverters.

The N.2304 cutting tables consist of a steel structure with a machined top plane where the motorized transport band lies. The band is rubber covered to avoid slab slipping during the cutting process. A stone blocking device, placed in the second transverse cutter table, allows reducing times during the transverse cut process considerably.

The table N. 2590, placed just after the longitudinal cutter, counts with a stop system, pneumatically driven, that allows the selection of the previously cut stone strips according to the width for their further processing in the longitudinal cutter.

The second table N.2585 counts with a towing device to join and align the strips before their processing in the transverse cutter, and to remove waste from the longitudinal cut.

The unloading table with band N. 2426 count with a steel profiles frame with a transport band to unload the cutting table while the transverse cutter receives and starts cutting the next panel.

The palletising robot N-3530 (optional) with vacuum suction cup is specially design to do automatic palletising tasks on the basis of the same operation principles applied in the Nodosafer standard palletising. It also offers many advantages such as work process optimisation, shorter cycle times and efficient use of the down times. The reception suction cup, with a special design, counts with a rectangular plate, able to support horizontal loads of up to 120 kilograms.

All dangerous working areas are isolated from personnel access by means of protection fences and optical barriers.

All machines and cutting heads count with a centralized greasing system for an easy and quick maintenance.

As for electricity and control, it is worth mentioning the use of last generation automatons with programs specifically designed by our technicians, so that the machine programming is as easy as possible, avoiding unnecessary loss of time. The operation cycle programming and the visualization of this sequence is made over two screen operator terminals where all the cutting parameters are displayed.

LOADING TROLLEY N.1289-P/V FEATURES
Table dimensions 1880x3200 mm
Frame dimensions 2560x1140 mm
Central vacuum 30 m3/h / 1.35 CV
Hydraulic control unit 5,5 CV
Trolley advance engine power 3 CV
Table engine power 1,5 CV
Trolley displacement speed 5 m/min
Stone sheet displacement speed 11.5 m/min
Maximum working width 2200 mm

MOTORIZED ROLLER TABLE N.2274/2200 FEATURES
Table width 2930 mm
Maximum table length 3500 mm
Maximum working width 2200 mm
Forward speed 11.5 m/min
Drive engine power 1.5 HP

BRIDGE CUTTER N.8000-L-600-5C FEATURES
Machine width 4220 mm
Rolling ways length 6000 mm
Maximum disks distance 1-5 2200mm (inside)
Minimum disks distance 1-2-3-4-5 300 mm
Cutting disks diameter 600 mm
Maximum height of the cutting pieces 150 mm
Disk engine power 15HP (5)
Total power installed 82 HP
Water consumption per disk 15-20 l/min

BRIDGE CUTTER N.8000-T-600-7C FEATURES
Machine width 5370 mm
Rolling ways length 5500 mm
Maximum disks distance 1-3 3500 mm (inside)
Minimum disks distance 1-2-3-4-5-6-7 300 mm
Cutting disks diameter 600 mm
Maximum height of the cutting pieces 150 mm
Disk engine power 15HP (7)
Total power installed 132 HP
Water consumption per disk 15-20 l/min

BAND CUTTING TABLE N.2304/2200 FEATURES
Table width 2960 mm
Max. Table length 4044 mm
Max. Band width 2200 mm (inside)
Band displacement speed 11.5 m/min
Drive engine power 3 HP

DOUBLE DISPLACEMENT MOTORIZED ROLLER TABLE N.2585/2200 FEATURES
Table width 2930 mm
Max. table length 3900 mm
Max. working width 2200 mm
Rollers forward speed 11.5 m/min
Roller drive engine power 1.5 CV
Centring displacement speed 5 m/min
Transversal displacement engine power 2.5 HP

ROLLER TABLE WITH SELECTION STOPS N.2590/2200 FEATURES
Table width 2930 mm
Max. table length 3700 mm
Max. working width 2200 mm
Rollers forward speed 11.5 m/min
Roller drive engine power 1.5 HP

MOTORIZED BAND TABLE N.2426/2200 FEATURES
Table width 2930 mm
Max. table length 4300 mm
Max. working width 2200 mm
Rollers forward speed 11.5 m/min
Roller drive engine power 3 KW

PALLETISING ROBOT N-3530 FEATURES
Max. load 120 kgs.
Mínimum piece size 300 x 300 mm
Central vacuum 100 m3/h
Installed power 25 CV
Minimum cycle time. 10” sec

The MILLENNIUM CNC 5X Indianapolis High Production Cutter is a new concept conveyor belt cutter designed by De La Cruz Stone Technology.
It is equipped with a lifting input table through which the material will be loaded, then by means of the motors equipped in each of the tables, the loaded material will pass to the belt, placing itself exactly in the cutting area to start working. Once the cut is finished, the material will go to the output table, where the material will be removed with suction cups or specialized material. Our team of engineers and designers have worked tirelessly for years to create and refine this concept that will allow fabricators to customize machines to meet all of their future cutting needs.

Cross cutting machine with single blade, swivel table and tilting bridge H45R. Ref 8802
Cross cutting machine with single blade, swivel table and tilting bridge
Simple and precise to cut in miter and / or false square to cut marble, granite, quartz, porcelain and solid surfaces.
The tilting head allows the blade to cut from 0º to +45 to make miter cuts easily, quickly and accurately.
The work bench is rotatable from + 45º to -45º to cut false square.
The machine is built with a monoblock structure, it does not need a foundation. It is also equipped with a basin that collects the residual water.
The workbench is made up of a series of plastic rollers (not motorized) installed on supports parallel to each other, which maintain the horizontal plane and rotate the degrees set by the operator on the display, with respect to the direction of advance of the disc. cut.
The workbench is equipped with a pneumatic clamping system that locks the material against the feed guide when cutting the diamond blade.
The head carrier bridge moves from 0º to + 45º from the vertical position. The rotation movement is mechanical and controlled from the display.
On this bridge composed of chrome bars, protected and with self-lubricating bushings, the cutting head moves.
In the upper part of the bridge is the control panel, with the functions of forward, backward, emergency stop, spindle forward speed, degrees of rotation of the workbench, to allow easy operation of the machine according to the safety rules.
The cutting head is equipped with an electric motor that transmits through V-belts and in a position where it is protected from water. The head is built in a way that prevents dirt from entering when working.
The cutting unit is equipped with a valve for cooling the blade.
The electrical system is installed in an electrical panel on the machine, on one side. The frequency variator is installed in this box to adjust the cutting head advance speed. Also installed are the display of the degrees of rotation of the bench and display of the degrees of inclination of the head.
The header is built to do the following movements:
Head disc cutting movement
Advance of the cutting head carriage by means of a gear motor
Rotating movement of the workbench by button
Bridge tilt movement via button
Locking by means of pneumatic cylinders to the two mobile jaws.
Technical characteristics:
Cutting heads: 1
Worktop height: 875mm 8up to 925mm)
Maximum useful cutting width with the bench at 0º: 850mm
Maximum useful cutting width with the bench at + 45º or -45º: 610mm
Maximum thickness: 75mm (bridge at 0º) 50mm (bridge at +45)
Idler Roller Workbench Length: 2,850mm
Maximum disc diameter: 400mm (hole 50mm)
Bank rotation: all degrees are shown on the display from 0º to +45 or 45º
Rotation of the head carrier bridge: All degrees are shown on the display from 0º to + 45º
Disc motor power: 7.5Kw

Cantilever cranes are a good solution when you need to serve multiple workstations without covering the entire width of the workshop and / or there are mobility limitations on the ground.

MILLENNIUM 420 CNC 4X Daytona Work Center: This is our high-end work center. A unique machine and a benchmark in the market due to its characteristics, among which stand out a robust monoblock structure, all movement systems in an oil bath and a total protection system in stainless steel.
We make the MILLENNIUM420 CNC 4X Daytona machining center in accordance with the highest quality standards for CNC machining centers, which guarantees maximum productivity and precision, high levels of finish, as well as high durability and minimum maintenance costs.

CNC stoneworking center with reduced dimensions.
Based on HCT-A model, we create a new stoneworking center which is more compact. In this way we put forward a high quality and strong machine with the necessary dimensions so that it can be placed in smaller workshoops.
It has a warehouse which is provided with 15 tools and it also has a working surface of 2600x1450mm, so that it allows to produce the most common stones for sinks and cooking tops.
Thanks to the innovative programming system of Canigó, the software which controls the machine is based on icons so it is extremely easy to use. It is not needed a special computer knowledge.
HCT-A compact machine is the opportunity for automate any workshop without the handicap of the machine dimensions and price.
UNIVERSAL WORK CENTER model HCT-A compact
STANDARD TECHNICAL CHARACTERISTICS
MOTORS
Disk motor power................................................................................ 5,5 KW
Adjustable turning speed of the head engine...................................... 7000 rpm
HEAD
No titling head.
Cutting systems................................................................................... Drill
Systems of the tools fixation............................................................... Automatic
AXIS STROKES AND MOVEMENTS
Vertical stroke of the head (axis Z)..................................................... 400 mm
Vertical movement of the head........................................................... Automatic
Transversal stroke of the bridge (axis Y)............................................ 1450 mm
Transversal movement of the bridge................................................... Automatic
Longitudinal stroke of the bridge (axis X)............................................ 2600 mm
Longitudinal movement of the bridge.................................................. Automatic
TABLE
Useful table surface…......................................................................... 2600x1450 mm
AUTOMATISMS
Laser pointer for the positioning of the material.
Automatic system of change of tools.
STRUCTURE AND COMPONENTS
Store of tools for 15 units..
Fixation of the material through adjustable suction pads.
Centralized lubrication.
Remote control for the manual positioning of the head.
TECHNICAL DATAS
Pressure of compressed air................................................................ 6 bars
Approximate net weight of the machine and accessories................... 4000 Kg.
External sizes of the machine............................................................. 4810x2950x2920 mm
INCLUDES THE FOLLOWING SERVICES
Vacuum plant with 4 suction pads of double effect of 120 mm.
Basic kit of tools and locking cones.
Training course

The MEB 2000 wire saw from Grani Roc is a machine designed for dressing and slabbing stone blocks. The machine is built with the classic setup of static structure and rotating trolley to position and to move the block.
· The bridge structure and pillars of the machine are built in laminated steel. All surfaces of contact between the different parts are machined for guaranteeing high precision in assembly and also in the cutting process.
· All the steel elements of the structure are subjected to a surface finishing consisting of a deep cleaning and degreasing treatment, a metallization treatment and corresponding protective layers and painting. These treatments enhance the durability of the machine
against aggressive weather and working conditions.
· The main motor is direct in the main pulley, and it is controlled by an electronic frequency variator –inverter-, that permits to apply progressive linear speed to the wire and its adjustment to optimize the behaviour and performance of the tool.
· The tensioning of the wire is made pneumatic and automatically with indication of wire breakage or shortage. In this way the machine controls automatically the down movement of the machine, adapting it to the optimum working tension of the wire, avoiding possible breakages
and optimizing its behaviour.
· All the main pulleys –drive and tensioning– and guiding wheels are protected by rubber liners in order to get the necessary traction of the wire. Such liners can be easily changed once they are worn out.
· The machine is equipped with an automatic cooling system for the diamond wire with detection of constant water pressure. This system stops the machine in the case of lack or insufficient water flow, protecting the tool and preventing possible deterioration or damage of the equipment.
· All the up and down screws are protected with hoods against dust and water .
· The machines has an automatic greasing system that injects lubricating liquid in the critical parts of the machine ensuring their correct functioning and the long life of the spare parts.
· The control panel is situated in the lateral part of the machine and moves with it. It has all the drive and protection components and devices of all control and safety equipment of the machine. All these components are standard, allowing easy and quick maintenance and / or replacement.
·The machine has its own mobile compressor, necessary for the pneumatic system for tensioning the wire.
·The trolley is 2.300 x 2.300 mm and has a maximum capacity of 30 Ton. The rotation is manual 360º and can be blocked every 90º.

Technical Features
Polishing Motor 5 HP
Lift motor 1 hp
Total power 6 hp
Automatic up-down, useful elevation 300mm
Smoother engine starter, to avoid wear on hooks and bearings
6 plates grinding ? 250, with 3 hooks each
Reinforced central head, more robust and durable
Piston pneumatic clamping, polishing with pressure

Up Lifting is a company which specializes in the development and manufacture of forklift trucks and large tonnage cranes. Integrated into the Gaypu group , which has 50 years experience in the metal industry, Up Lifting provides its customers with solutions for the loading, unloading and handling of products in varied environments.

H600-CP / H600-L Single Blade Automatic Step Cross Cutting Machine
Cross cutting machine with single blade, transport belt and automatic multiple pass.
H600-CP cross cutting machine allows multiple pass cutting of hard and thick material up to 100mm(or up to 200mm in the H600-L version), guaranteeing at the same time the possibility of single pas cutting.

GH 788-
Place of installation: Colombia
Capacity: 10t
Span: 23m
Lifting height: 8m
GH 757
Place of installation: Thailand
Capacity: 32t
Span: 25m
Lifting height: 7m
GH, European leader in design and manufacture of Gantry Cranes (also referred to as Portal Cranes and Goliath Cranes).
The number of Gantry Cranes installed
turns us into the reference.
GH adapt his Gantry Cranes manufacturing process to the different customer´s requirements, taking care of which kind of work is going to performance.
Gantry cranes and portal cranes from GH Cranes & Components feature vertical legs on wheels that move along fixed runways, typically at floor level. They are highly efficient at moving heavy loads at high speeds, and are used largely outdoors.
Our gained experience from 1958 backed up as specialists in Portal and Semi Portal Cranes.
Lifting capacity: 400T.

Automatic cross cutting with one disc HSA-1
Automatic cross cutting HSA is a cutter to improve the optimization and use of marble, granite, porcelain and sintered stone.
Cuts different width measurements in a single pass with precision and productivity.
Strong and robust structure to support and move heavy parts
Motorized rubber belt to move the pieces to be cut, with 2 speeds of forward. A fast one to reach the desired measure and another slow one to position the material to the exact measure.
Pneumatic clamps to fix the part during cutting
Belt motor head that allows the disc revolutions to be varied according to the material to be cut.
Manual height adjustment that allows adjusting the cutting depth of the blade on the belt
Inverter that regulates the cutting advance speed of the head. In the final stage of cutting, the feed is automatically reduced to eliminate breaks in the material.
It is completed with a rapid return of the head reducing machining times.
The machine is equipped with a PLC that controls the different processing phases.
By means of a touch screen the operator can regulate and control the work cycles
Cut to size via joystick display
The operator takes the material close to the disc to make the first cut, and performs the recognition of the measurement using the joystick. In this way the measure is entered into the machine. You can enter different lengths.
Sequential automatic cut to size
The operator can enter a measurement on the screen (maximum 6)
set one of the following sequences
cutting sequences of different sizes
cutting sequence of a single repeating quota or multiple repeating dimensions
Cutting sequences can be combined with different material widths, creating a useful database for the operator.

Do you need a jib crane for an industrial manufacturing or port application? Then consider a jib crane from GH Cranes & Components, one of the 5 largest crane manufacturer in the world.
Jib cranes from GH Cranes & Components come in four styles: wall jib cranes, column jib cranes, industrial jib cranes and port jib cranes.
Our jib cranes are the ideal solution when you must move loads in a circular direction next to a manufacturing station. They feature an integrated lifting mechanism, typically a chain or wire rope hoist that is either manual or motorized.
Jib Cranes from 125 kg to 20 ton.

MILLENNIUM 420 CNC 4X Daytona Jumbo Work Center: It is our high-end work center. A unique machine and a benchmark in the market due to its characteristics, among which stand out a robust monoblock structure, all movement systems in an oil bath and a total protection system in stainless steel.
We make the MILLENNIUM420 CNC 4X Daytona Jumbo machining center in accordance with the highest quality standards for CNC machining centers, which guarantees maximum productivity and precision, high levels of finish, as well as high durability and minimum maintenance costs.

Single disc cutter to perform simple and easy cutting jobs, on slabs, steps, baseboards or curbs, in marble, granite, quartz or porcelain.
The surface that supports the piece to be cut is composed of idle nylon rollers to move the material easily. Mechanical stops always keep the piece tailored and aligned to obtain a square cut with precision.
Equipped with a motor that transmits to the shaft by belts. In this way, the revolutions of the disc can be varied, depending on the material to be cut.
It automatically reduces the feedrate of the head in the terminal phase of the cut to avoid material breakage. Making the return of the head quickly and automatically reducing cutting times.

Single-Girder Electric Hoists
Low-headroom hoists
Low-headroom hoists are perfect for using in the small under-beam space in single-girder cranes.
Choose between flat or angled wheels to suit your bottom flanges and running profile, to improve performance and increase the life of your hoist.
Low Headroom single girder hoists
Standard-headroom hoists
Our standard-headroom hoists are the perfect solution when the amount of space under your single-girder crane is not critical, or when you are moving loads between halls.
This configuration is suitable for 1/1 and 2/2 reeving hoists.
Choose between flat or angled wheels to suit your bottom flanges and running profile, to improve performance and increase the life of your hoist.
Normal headroom single girder electric hoists
Standard-headroom hoists ready for curves
This hoist is designed for applications that involve moving loads along paths with turns and changes of direction.
Choose between flat or angled wheels to suit your bottom flanges and running profile, to improve performance and increase the life of your hoist.
Normal headroom single girder electric hoists ready for curves
Double-Girder Electric Hoists
Compact hoists
GH compact hoists are the most compact double-girder hoists available today. Their simple yet robust design makes them ideal for multiple applications that require a compact hoist.
Compact double girder electric hoists
Hoists on end carriages
GH manufacturers a number of hoists that are designed for trolleys with two hoists, rotating trolleys, and other applications that involve end carriages.
Available options include a manual brake release, weighing system and additional safety brake.
Double girder electric hoists on end carriage
Nested hoists
Our nested double-girder hoist is ideal when little space is available between the top of the girders and your roof. We design the trolley to place the hoist between the girders.

The HM-2 cross cutting machine combines the possibility of cutting with two units with the positioning precision of the mobile spindle, employing advanced technologies when cutting strips of marble and granite. It finds its application in consecutive cuts of different sizes and is ideal for recovering waste material.

60 tons heavy forklit.

Container loader Boards
HELPFUL uploads and downloads PACKAGES OF TABLES
Undoubtedly one of the most efficient in the process of boosting transport marble tables tools. This tool allows upload and download packages of tablets in closed containers with the crane, as reflected in the next picture.
features
Weight: 1,440 kg.
Max Load Weight: 4 Tons
Crane load. Min 5 Ton
Dimensions: L 6000 mm. X 1500 mm

The MEB 2000 wire saw from Grani Roc is a machine designed for dressing and slabbing stone blocks. The machine is built with the classic setup of static structure and rotating trolley to position and to move the block.
· The bridge structure and pillars of the machine are built in laminated steel. All surfaces of contact between the different parts are machined for guaranteeing high precision in assembly and also in the cutting process.
· All the steel elements of the structure are subjected to a surface finishing consisting of a deep cleaning and degreasing treatment, a metallization treatment and corresponding protective layers and painting. These treatments enhance the durability of the machine against aggressive weather and working conditions.
· The main motor is direct in the main pulley, and it is controlled by an electronic frequency variator –inverter-, that permits to apply progressive linear speed to the wire and its adjustment to optimize the behaviour and performance of the tool.
· The tensioning of the wire is made pneumatic and automatically with indication of wire breakage or shortage. In this way the machine controls automatically the down movement of the machine, adapting it to the optimum working tension of the wire, avoiding possible breakages
and optimizing its behaviour.
· All the main pulleys –drive and tensioning– and guiding wheels are protected by rubber liners in order to get the necessary traction of the wire. Such liners can be easily changed once they are worn out.
· The machine is equipped with an automatic cooling system for the diamond wire with detection of constant water pressure. This system stops the machine in the case of lack or insufficient water flow, protecting the tool and preventing possible deterioration or damage of the equipment.
· All the up and down screws are protected with hoods against dust and water .
· The machines has an automatic greasing system that injects lubricating liquid in the critical parts of the machine ensuring their correct functioning and the long life of the spare parts.
· The control panel is situated in the lateral part of the machine and moves with it. It has all the drive and protection components and devices of all control and safety equipment of the machine. All these components are standard, allowing easy and quick maintenance and / or replacement.
·The machine has its own mobile compressor, necessary for the pneumatic system for tensioning the wire.
· The trolley is 2.300 x 2.300 mm and has a maximum capacity of 30 Ton. The rotation is manual 360º and can be blocked every 90º.

TECHNICAL DATA:
- Dimension of the machine .............................. 7,000 x 2,000 x 2,000 mm
- Each motor power polisher ....................................................... 2 CV
- Motor power tilting system ................................................. 7 HP
- Total installed power .............................................. ............... 39 CV
- Motor power moldudador .............................................. 4 CV ..........
- Conveyor reducer ............................................. .. 2 CV
(electronic adjustable)
- Thickness to polish .................................................................................... 6 cm
- 1 Set drip-gauge ............................... tilt 0 ° to 90 °
- 6 engines polishers with automatic stop control programmatically.
- 2 + Bevelers Bevelers lower than
- 2 Blocks entered and output rollers
- The first engine works as moldurador, with mechanical working radius.
MACHINE
The machine is built in monoblock structure
By Crank Rocker System With Sealed bearings in oil bath
Programmable Automatic lubrication deposit. -
Securing pneumatic pistons mediantes stones with rubber rollers Accompaniment
Extensible support for Long pieces. -
System input and output rollers included. -
Table operation via large touch screen.
Shells of stainless steel machine

Slot/Kerf and drilling machine for cladding products KERF-2
Ref. 8503
The KERF-2 machine grooves and perforates coating products. It can have different finishes such as:
Kerf I continue
Kerf Reduced
Slot
Vertical drill
Horizontal drill
Incision

Bridge Image CNC cutter: equipped with high technology that allows high-precision and fast cuts.
Machine of easy placement and assembly that allows its rapid transfer, also occupying a reduced space.
The Image CNC Cutter allows the complete quartering of boards with great precision and speed, since its CNC control manages the sequence of all the movements and cuts of the process, reducing work time, both in its execution time and in its programming.

Machine that allows to obtain holes and cuts with great flexibility. Ref. 8502
Machine for cladding KERF-1000
Ref. 8502 Technical characteristics:
The main feature of the KERF-1000 coating machine is the extreme flexibility in processing that allows to obtain holes and cuts, depending on the configuration required by the customer.
The different types of finish for each anchor can be obtained with a single machine:
Kerf, Slot cutting and drilling

New Groover CNC of 12 axes for ventilated facades
HERSEN designs and manufactures special machinery, made to measure, for Large Format Porcelain, Porcelain Stoneware, Sintered Stone, Solid Surfaces, marbles and granites.
This automatic slotting machine makes incisions on the back of the pieces for the placement of the fixing system. In this case, for the STRONGFIX anchoring system. It is a 45 degree double groove in the shape of a dovetail. The aluminum profiles are inserted into these grooves and fixed to the piece with putty.
HERSEN has designed a router that performs a clean and precise cut, obtaining precise and defined incisions. It can slot parts from 100mm to 1600mm wide, which allows ENTIRE BOARDS to be slotted.
The material to be grooved enters through a motorized roller bed, and a controlled mobile guide correctly aligns the material before entering the machine and the heads begin to groove.
It is built with 6 motors installed on 3 bridges. Each bridge has an independent cutting head, composed of two motors with two discs, in this way it is possible to make 3 pairs of grooves at 45º at the same time and separated from each other to any size.
It performs the grooving both continuously and discontinuously. This discontinuous grooving makes it possible to groove parts where windows, doors or corner joints go without the grooving cut being seen by the edges. What makes the façade aesthetically improve and does not weaken the pieces by making unnecessary cuts.

It is also possible to build the machine for the transverse grooving of the board.
It has been equipped with an automatic control and measurement system for the wear of the diamond blades and the depth of the grooves to always obtain the desired measurement of the grooves. Another system automatically fans the diamond blades, optimizing the number of meters of cut and always allowing a clean cut in the incisions.
It has been implemented with custom made software to be able to manage the work orders and breakdowns of the architects. In this way, the execution of the pieces can be managed both from the machine and from the technical office. In this way, the pieces that are being made of each project and each facade are controlled at all times, as well as the pieces that still need to be done.

The cutting line N.2990/2200-5+7C counts with:

1 Intermediate motorized plastic rollers table, model N.2274.
1 longitudinal cutter with 5 cutting heads ø 600 and mobile bridge, model N.8000-L-5C.
1 transverse cutter with 7 cutting heads ø 600 and mobile bridge, model N.8000-L-7C.
2 motorized band cutting tables, model N.2304.
1 table with stone sheet selection stops, N. 2590.
1 double displacement table with motorized rollers, model N.2585.
1 motorized band table for material output, model N.2426.
CUTTING LINES N2990/2200 5 + 7 HEADS TECHNICAL SHEET
Our cutting line N.2990/2200-5+7C has been designed aiming maximum production capacity with minimum labour force, as well as the absolute reliability of all its parts.

The production line overall dimensions have been adjusted to the customer needs, following his criteria about the produced pieces dimensions and the final products obtained.

The whole line features better robustness and reliability in all its subassemblies, being them all designed to support the hardest working conditions. This is one of the most relevant aspects where we can offer our long time experience in designing and manufacturing stone processing machines for this sector.

One of the great advantages of the machines integrating this production line is that all the designs are already tested solutions. They only differ from our standard machines in their overall dimensions, but not in all incorporated components.

With the automatic loading trolley NDF-1289-P/V (optional), the longitudinal cutter is fed with material from a stacker. Panels are removed using suction cups connected to a vacuum pump that tilt and place them in a horizontal position, ready to move to the cutting unit. Panels from the horizontal stacker are placed waiting to enter in the production line in such a way that the following panels maintain the alignment being unnecessary to adjust the cutter starting point.

The intermediate rollers table not only joins the feeding trolley and the longitudinal cutter but also acts as an intermediate storage so that the cutting unit stop times are very low.

The 5 heads longitudinal cutter N.8000-L-5C over rolling bridge and the 7 heads transverse cutter N.8000-T-7C are equipped with the latest technology, both in their mechanical design and in their electronics. It is worth mentioning the use of a high precision and stiffness linear guide system with linear recirculating ball bearing unit by the gripper cutting head bridge during the cutting works. The bridge is supported by two beams, being parallel to the cutting table the first and perpendicular, the second.

The sliding disc holder cutting heads also move vertically guided by a linear recirculating ball bearing unit and operated by a laminated ball screw with recirculating ball screw nut in order to achieve a quick and precise positioning and being all perfectly protected by PVC bellows. The gripper cutting heads have translation movement thanks to a gear motor controlled by a frequency inverter and positioning magnetic scale in the X axis and cutting head operated by a ball screw and an electric gear motor for vertical positioning in the Z axis. The cutting heads positioning is simultaneous thanks to their independent inverters.

The N.2304 cutting tables consist of a steel structure with a machined top plane where the motorized transport band lies. The band is rubber covered to avoid slab slipping during the cutting process. A stone blocking device, placed in the second transverse cutter table, allows reducing times during the transverse cut process considerably.

The table N. 2590, placed just after the longitudinal cutter, counts with a stop system, pneumatically driven, that allows the selection of the previously cut stone strips according to the width for their further processing in the longitudinal cutter.

The second table N.2585 counts with a towing device to join and align the strips before their processing in the transverse cutter, and to remove waste from the longitudinal cut.

The unloading table with band N. 2426 count with a steel profiles frame with a transport band to unload the cutting table while the transverse cutter receives and starts cutting the next panel.

The palletising robot N-3530 (optional) with vacuum suction cup is specially design to do automatic palletising tasks on the basis of the same operation principles applied in the Nodosafer standard palletising. It also offers many advantages such as work process optimisation, shorter cycle times and efficient use of the down times. The reception suction cup, with a special design, counts with a rectangular plate, able to support horizontal loads of up to 120 kilograms.

All dangerous working areas are isolated from personnel access by means of protection fences and optical barriers.

All machines and cutting heads count with a centralized greasing system for an easy and quick maintenance.

As for electricity and control, it is worth mentioning the use of last generation automatons with programs specifically designed by our technicians, so that the machine programming is as easy as possible, avoiding unnecessary loss of time. The operation cycle programming and the visualization of this sequence is made over two screen operator terminals where all the cutting parameters are displayed.

LOADING TROLLEY N.1289-P/V FEATURES
Table dimensions 1880x3200 mm
Frame dimensions 2560x1140 mm
Central vacuum 30 m3/h / 1.35 CV
Hydraulic control unit 5,5 CV
Trolley advance engine power 3 CV
Table engine power 1,5 CV
Trolley displacement speed 5 m/min
Stone sheet displacement speed 11.5 m/min
Maximum working width 2200 mm

MOTORIZED ROLLER TABLE N.2274/2200 FEATURES
Table width 2930 mm
Maximum table length 3500 mm
Maximum working width 2200 mm
Forward speed 11.5 m/min
Drive engine power 1.5 HP

BRIDGE CUTTER N.8000-L-600-5C FEATURES
Machine width 4220 mm
Rolling ways length 6000 mm
Maximum disks distance 1-5 2200mm (inside)
Minimum disks distance 1-2-3-4-5 300 mm
Cutting disks diameter 600 mm
Maximum height of the cutting pieces 150 mm
Disk engine power 15HP (5)
Total power installed 82 HP
Water consumption per disk 15-20 l/min

BRIDGE CUTTER N.8000-T-600-7C FEATURES
Machine width 5370 mm
Rolling ways length 5500 mm
Maximum disks distance 1-3 3500 mm (inside)
Minimum disks distance 1-2-3-4-5-6-7 300 mm
Cutting disks diameter 600 mm
Maximum height of the cutting pieces 150 mm
Disk engine power 15HP (7)
Total power installed 132 HP
Water consumption per disk 15-20 l/min

BAND CUTTING TABLE N.2304/2200 FEATURES
Table width 2960 mm
Max. Table length 4044 mm
Max. Band width 2200 mm (inside)
Band displacement speed 11.5 m/min
Drive engine power 3 HP

DOUBLE DISPLACEMENT MOTORIZED ROLLER TABLE N.2585/2200 FEATURES
Table width 2930 mm
Max. table length 3900 mm
Max. working width 2200 mm
Rollers forward speed 11.5 m/min
Roller drive engine power 1.5 CV
Centring displacement speed 5 m/min
Transversal displacement engine power 2.5 HP

ROLLER TABLE WITH SELECTION STOPS N.2590/2200 FEATURES
Table width 2930 mm
Max. table length 3700 mm
Max. working width 2200 mm
Rollers forward speed 11.5 m/min
Roller drive engine power 1.5 HP

MOTORIZED BAND TABLE N.2426/2200 FEATURES
Table width 2930 mm
Max. table length 4300 mm
Max. working width 2200 mm
Rollers forward speed 11.5 m/min
Roller drive engine power 3 KW

PALLETISING ROBOT N-3530 FEATURES
Max. load 120 kgs.
Mínimum piece size 300 x 300 mm
Central vacuum 100 m3/h
Installed power 25 CV
Minimum cycle time. 10” sec

Line for the production of pavers from slabs sawn on both sides. The line is based on three levels of shearing and a robotic cell with artificial vision:
1. Primary shearing 1st: Generates strips of granite from the slab. Maximum dimensions determined by the maximum working width of the shear.
2. 2nd Secondary Shears: Processes the strips from the primary shear, generating paver to be palletized by the robot or paver to be unfolded in half in the 3rd shears.
3. Tertiary shears 3rd: Secondary shears split the cobblestones in half. 4. Robotic cell: Robotic cell for handling pavers, equipped with artificial vision that allows the robot to handle the pavers automatically. At this point we can palletize the pavers on a pallet, or split them in half with the 3rd shears.

WATER AND AIR FILTER SYSTEM
FILTEREVO
Water filtration systems recycle the water used in stone processing. They help to significantly reduce costs, ensure sufficient quality of the recycled water and enable environmentally friendly operation.
Air cleaning systems are designed to filter 99% of the air in dusty work areas.
The suction cabin of the dry filter system is designed to filter the air in dusty work areas without the need for water and with low noise levels. The filtration system can be adjusted to the type of dust.
The water suction system is a conventional air cleaning system that uses water to moisten the dust during the cleaning process, trapping it in its entirety.

Eight points vacuum for sandwich panels with depressor and radio control
Ref. 50790-8 technical characteristics:
Load capacity: 300kg
Tare: 200kg
Extensible structure with two telescopic arms:
Length collected: 4m
Stretched length: 7m
Tipping equipment in all directions without loss of oil or acids
Balance with ropes to be able to make the turn up to 90º
Suction cups with anti-oil rubber and mounted on a suction cup with springs
Compressed air supply
Pump group with:
Rotary pump
Double tank
Double tap circuit
Visualization and vacuum control
Anti-drop valve
Vacuum filter
Condensation filter
Action with ball valve
Batteries with gel charge and 24 volt power plus spare battery
Acoustic-visual alarm in reference to the minimum / maximum pressure
Accidental anti-drop device
Remote radio control